JL Audio CR-1 страница 28 Скачать руководство пользователя

Страница: 28 / 28

FEATURES

Power Modes:

Off/On, selectable via front panel switch
Crossover Function:

Bypass or On,

selectable via front panel switch
Subwoofer Output Modes:

Mono L+R or Stereo,

selectable via front panel switch
Crossover Frequency Range:

30 Hz – 150 Hz, variable with

independent high-pass and low-pass filter

frequency controls on front panel
Crossover Slopes:

12 dB/octave or 24 dB/octave, Linkwitz-

Riley, selectable via front panel switch
Subwoofer/Satellite Balance Control:

+/– 12 dB, fully variable via front panel knob
Filter Damping Controls:

Q: 0.3 - 1.4 @ 12 dB/octave,

via front panel knob

Q: 0.16 - 4.0 @ 24 dB/octave,

via front panel knob

For either slope, Q = 0.5

at top dead center “0” mark
Output Muting:

independent for each output, via front

panel push-button switches
Ground Lift (Balanced Connections):

Isolated/Grounded, via rear panel switch

Specifications

CR-1

Maximum Input Voltage:

8 Vrms (+18 dBv)

Input Impedance:

Unbalanced: 50 kΩ

Balanced: 20 kΩ

Maximum Output Voltage:

8 Vrms (+18 dBv)

Output Impedance:

Unbalanced: 150 Ω

Balanced: 300 Ω

THD + Noise:

< 0.002% at 8 Vrms/10 kΩ

20 Hz - 20 kHz, 90 kHz bandwidth

Signal to Noise Ratio:

>115 dB, referred to rated output voltage

Channel Separation:

80 dB at 1 kHz, typical

Low Pass Frequency Response:

+0, -1 dB from 5 Hz to 1/4 of filter frequency

High Pass Frequency Response:

+0, -1 dB from 4x filter frequency to 80 kHz

Power Consumption:

30 Watts (typical, with or without signal)

Mains Voltage (Frequency):

120V (60 Hz) or 230/240V (50 Hz or 60 Hz),

factory-set for destination country (see back panel of CR-1)

Table-Top

Dimensions: (H) Height x (W) Width x (D) Depth

3.80 in x 17.40 in x 15.67 in

97 mm x 441 mm x 398 mm

Rack-Mount

Dimensions: (H) Height x (W) Width x (D) Depth

3.46 in x 19.07 in x 15.67 in

88 mm x 484 mm x 398 mm

T O P V I E W

B A C K P A N E L

F R O N T P A N E L

w w w . j l a u d i o . c o m

10369 North Commerce Parkway • Miramar, Florida • 33025 • USA

#6,118,884 #6,229,902 #6,243,479 #6,294,959 #6,501,844 #6,496,590 #6,441,685 #5,687,247 #6,219,431 #6,625,292 #D472,891 #D480,709 • Other U.S. & Foreign

patents pending. For more detailed information please visit us online at

www.jlaudio.com.

Due to our policy of continuous product development, all specifications

are subject to change without notice.

SKU#97262 06022014-Rev.2

Printed in U.S.A.

Содержание CR-1





























Результаты поиска

Содержание CR-1

Отзывы:

Похожие инструкции для CR-1

Бренды по названию

Популярные бренды

JL Audio CR-1, Руководство пользователя

Результаты поиска

Содержание CR-1

Отзывы:

Похожие инструкции для CR-1

Бренды по названию

Популярные бренды