JL Audio CR-1 страница 22 Скачать руководство пользователя

Страница: 22 / 28

CR-1

Page 22

SCENARIO 2 SETUP GUIDE:

2-channel Subwoofer/Satellite System that is Bass-Managed by the CR-1 and also
shares active subwoofers with a separate multi-channel home theater system

For this setup discussion, we will assume that your separate home theater

system is already working and optimized using the subwoofers you will

share with the stereo system and the CR-1. Dedicated stereo speakers that are

completely separate from your Home Theater system will be added, along with a

stereo preamp, a stereo amplifier, and the CR-1.

Connect your CR-1 as shown in Scenario 2 Connection Diagram on page 17.

It is very helpful if your existing Home Theater setup has resulted in

Subwoofer Level Controls set at a middle position (“0” on a JL Audio subwoofer’s

Master Level) and your home theater receiver or processor’s subwoofer output

level is also at a middle-range reference position. This will ensure easier

integration of your dedicated stereo system and the CR-1.

If you raise the existing Subwoofer Master Level (on the powered subwoofer)

to level match the two-channel system, you will need to LOWER the subwoofer

level in your home theater receiver or processor to compensate for this level shift.

Likewise, if you lower the Subwoofer Master Level to match the two-channel

system, you will need to RAISE the subwoofer level in your home theater receiver

or processor to compensate for that level shift. The goal is to find a common

setting of the Subwoofer’s Master Level control that works well for both systems

– the home theater receiver or processor’s level control is used to offset any level

differences that exist. The CR-1’s Sub/Sat Balance control is intended for fine

tuning rather than gross level offsets.

First, you will set up the two-channel portion of the system, using the CR-1’s

controls. Use the same settings and follow the exact same procedures listed in

Setup Scenario 1 to set up this 2-channel mode.

Once you have completed the 2-channel setup and are happy with the

results, switch the CR-1 into “Bypass” mode via the front panel switch,

and confirm that your subwoofer level played through your home theater

receiver or processor is still correct. As mentioned above, your 2-channel

system’s subwoofer level will be determined only by the Subwoofer’s

Master Level control. Your HT receiver or processor’s subwoofer level will

adjust the output for multi-channel mode. If needed, adjust the home-

theater mode’s subwoofer level via the HT receiver or processor.

Once the above is accomplished, your Home Theater system should sound

normal when the CR-1 is in Bypass mode AND your two-channel subwoofer/

satellite system should sound fantastic as well. The CR-1 has successfully allowed

you to share subwoofers between two different systems with the push of one button.

Содержание CR-1





























Результаты поиска

Содержание CR-1

Отзывы:

Похожие инструкции для CR-1

Бренды по названию

Популярные бренды

JL Audio CR-1, Руководство пользователя

Результаты поиска

Содержание CR-1

Отзывы:

Похожие инструкции для CR-1

Бренды по названию

Популярные бренды