background image

JR Flexo Press Series

7

I.

Operating principle

When the machine is switched on, the anilox roller will rotate in the ink duct. By

controlling the clearance between the ink scraper and the anilox roller, you can deliver a

proper amount of ink evenly to the flexographic plate of the circumferential surface of the

printing plate wheel. The flexographic plate roller carries the ink to the surface of the

material to be printed, which is dried and rolled by the electrically heated drying board to

finish the process. The printed material is then put into the electric thermostat ventilating

and drying cabinet for about 5 and 6 hours, with the effect of fast color and tolerant laundry.

Environment friendly, the machine is characterized by its speed and efficiency.

Structure

i.

Operating principle of photoelectric controlled band-feeder

There are two modes in the setting: ON and OFF. When the machine is in the ON mode,

the photoelectric switch must be screened by the material for the machine to start up. When

the material has been printed, the machine stops working.

Ii None Stop Register

First make rough positioning. Press in the printing cylinder. When the error of the

printing trace is around 3.5mm, accurate positioning can be made. However, when the

error is greater than 3.5mm, the gear must be withdrawn and turned to the necessary

position. Press in the printing cylinder again to make the error around 3.5mm. Switch on

Содержание JR1241
















Отзывы: