JIMS MILWAUKEE-EIGHT 5833 Скачать руководство пользователя

Страница: 10 / 10

CAUTION: Wear safety glasses over your eye’s.

See JIMS

catalog for Hundreds of top quality professional tools.

The last tools you will ever need to buy.

IIn

tiio

n S

t F

r T

l #

Rev N/C

7-19

No.5833-IS

555 Dawson Drive, Camarillo, CA 93012 Phone 805-482-6913 • Fax 805-482-7422

A Division of Thiessen Products, Inc.

15.

Align the Bearing Installer Pilot

#5833-2

with the balancer bearing bore and carefully lower

the Bearing Installer Pilot by rotating the Screw

#1024

clockwise until it bottoms out in the

balancer bearing bore, back off ¼ turn. DO NOT force the pilot into the bore or case dam-
age may result. Tighten the three 5/16-18 x 4” SHCS

#5833-5

, 5/16” washers

#1216

and

nuts

#1222

until tight with an Allen key.

See Fig. 7.

16.

Back the Bearing Installer Pilot

#5833-2

out by rotating counter clockwise, feeling for any

binding between the balancer bearing bore and the Bearing Installer Pilot. If binding is
detected, Loosen the three 5/16-18 x 4” SHCS

#5833-5

, 5/16” washers

#1216

and nuts

#1222

and re insert the Bearing Installer Pilot

#5833-2

and retighten the SHCS. Repeat until

there is no binding.

17.

Continue process -

Fig 8. - Step 9.

FIG.11

Содержание MILWAUKEE-EIGHT 5833











Результаты поиска

Содержание MILWAUKEE-EIGHT 5833

Отзывы:

Похожие инструкции для MILWAUKEE-EIGHT 5833

Бренды по названию

Популярные бренды

JIMS MILWAUKEE-EIGHT 5833, Инструкция

Результаты поиска

Содержание MILWAUKEE-EIGHT 5833

Отзывы:

Похожие инструкции для MILWAUKEE-EIGHT 5833

Бренды по названию

Популярные бренды