-4-
BATTERY OPERATING INSTRUCTIONS
LED
STATUS
OUTPUT
VOLTAGE
CONDITION
*NOTES
Off
No Output
Charger not plugged
in
Off
No Output
Output Shorted
Off
No Output
Battery Voltage
below 3Volts
2
Red
(blinking)
Vbatt 3-7Volts
typ.
Charging
1 & 2
Red
Vbatt 7-13Volts
typ.
Charging full Amps
(1 or 2A)
Yellow
Vbatt 13.0 -
13.5Volts
Charging < 70% full
Amps
Green
Vbatt 13.5Volts
Battery fully charged
(OR not connected)
Green
(blinking)
Vbatt >
13.5Volts
Check for incorrect
battery
3
*NOTES:
1. Vbatt is the battery voltage
2. Battery overly discharged; may not fully charge.
3. LED may blink momentarily if the above connection procedure is not
followed.
Always keep your internal AGM battery fully charged.
Plug your Battery Doc® Charger/Maintainer into any 110
volt outlet after each use. Battery Doc®
Charger/Maintainer will not over charge the battery.
External Battery Information (optional)
The JIFFY STX PROII LECTRIC requires a 12 volt, deep cycle, lead
acid battery. Jiffy recommends an AGM battery.
The power source should be chosen carefully. The battery directly
affects the performance of the drill. A battery that is too small or in
poor condition will reduce power and cycle time.
The battery should be
fully charged
before every use. This will
ensure maximum performance from both your JIFFY LECTRIC power
ice drill and the battery.
Use the included Jiffy part #3917, 8 ft Connection Cable to connect to
an external battery.
Replacement Blade
Improper cutting may be due to dull or damaged drill teeth or drill point.
Maintain sharp blade teeth and point. Preserve the original factory
cutting angles when sharpening your drill. File blade teeth and use a
disk sander to sharpen the point. For professional service see your
Jiffy service center. Only genuine Jiffy blade teeth are to be used.
Blade Replacement Instructions
When replacing blade teeth, the beveled edge of teeth and the head of
the capscrews should face the ice. The stamped part number on the
teeth should face away from the ice, as shown in the diagram. Use
two 7/16” wrenches to remove the capscrews and to retighten after
replacement. CAUTION –
THE BLADE TEETH ARE SHARP AND
SHOULD BE HANDLED CAREFULLY TO AVOID FLESH CUTS OR
INJURY.
JIFFY® PROII LECTRIC™ ICE DRILL –
PARTS LIST
Ref.
Part
No.
No.
No.
Description
Used
1
4155
Cover
1
2
1719
Locknut
2
3
4289
Machine Screw
2
4
3810
Motor
1
5
3918
Wire Assembly
1
6
4261
Battery
1
7
4265
Wire Assembly
1
8
2512
Push Nut
2
9
3961
Switch
1
10
3968
“U” Handle
1
11
4270
Throttle Clip
1
12
4150
Throttle Assembly
1
13
4152
Switch Mounting Bracket
1
14
4266
Wire Assembly
1
15
2451
Locknut
2
16
4151
Battery Holder
1
17
4156
Hex Capscrew
2
18
3946
Handle Plate
1
19
4153
Battery Clamp
1
20
3921
Motor Mounting Plate
1
21
1683
Hex Capscrew
1
22
1689
Flat Washer
8
23
1119
Lock Washer
1
24
4154
Plug Bracket
1
25
4267
Cable Asbly w/ Connector 1
26
3965
“L” Handle
1
27
2355
Hex Capscrew
4
28
3922
Locknut
6
29
4269
Machine Screw
2
30
2336
Locknut
2
31
3351
Hex Capscrew
2
