background image

                                                                                                                   

User’s Manual

 

22 

 

 

                   

Figure 4.12                                              Figure 4.13

 

2

3G Module Installation 

a. Demount the connection line into 5 parts as shown in figure. 

 

 

                   

Figure 4.14                                                  Figure 4.15 

b. Fix one end of the wire on the right hole of panel, and the other end of the wire on the 3G 
module as shown in figure.   

   

 

                    Figure 4.16                                              Figure 4.17

 

c. Fix the antenna on the connection wire which was fixed in the side of panel. 

 

 

                      Figure 4.18                                            Figure 4.19

 

3

GPS Module Install 

a. Demount the connection line into 5 parts as shown in figure. 

Notice: 

MSATA 
Position

 

Connetion 

wire 

Antenna

 

Notice: 

The connection 

wire include 5 

parts.

 

Notice: 

Fix the other end of 

connection wire like 

this.

 

Notice: 

Antenna fixed in 

connection line are 

shown at the exit

 

Содержание FEBC-3150










































Отзывы: