JF FCT 1460 Скачать руководство пользователя страница 70 | Manualshive

Страница: 70 / 114

JF FCT 1460 Скачать руководство пользователя страница 70

5. METAL DETECTOR (MD)

PIGB-206X-02 FCT1460 0614

- 70 -

Fig. 5-7

The metal detector is turned on and off by pushing the button on the MD control unit.
It is turned

off

by holding the button for about 5 seconds. Thereby the yellow control

light on the MD control unit and the light on the control box are turned off. One single
push on the button turns on the metal detector again.
Although the metal detector has been turned off, it is always turned on when the
machine starts, when the control unit has been turned off on the control box or when
the power supply has been interrupted.

This ensures that you don’t work without

metal detector unless you intend to. If you work without metal detector you risk that
metal enters the machine, causing damage and contamination of the crop.

WARNING:

Do not approach the machine when the feed intake is in neutral
position and the rotor is rotating. Neutral position does not
guarantee that the feed intake will not start.

The MD control unit controls the reverse system in the following situations:



When the system is turned on:

The reverse moves to neutral position and

cannot move to feed intake until the machine

has reversed for 2 seconds.



When metal is registered:

(If turned on)

The reverse moves to neutral position and

cannot move to feed intake until the machine

has reversed for 2 seconds.

Fig. 5-7

«
...
68
69
70
71
72
...
»

Содержание FCT 1460



















































































































Отзывы:

Нет отзывов