background image

VT80BL Instruction Manual 

Page 4

JETS MUNT S.L

Warranty

  The warranty period for the VT80 is 2 years from the date of purchase, or 25 running
hours, whichever comes first. Warranty is valid solely for the original owner and is non
transferable upon resale.
  Warranty includes all supplied parts, and is limited to manufacturing and material defects
only. Shipment costs, including packing and customs fees are not covered by the warranty
and will be always at owner expense.

  Damage or defective operation covered under the warranty terms will be repaired and
tested at no cost the original owner (other than shipping expenses). Repairs not covered
under the terms of warranty will be carried out by Jets Munt SL or their appointed agents
after agreement of costs.

  Before returning the engine or ancillary equipment for service of repair, please contact
first to your local dealer or Jets Munt central office to agree action and costs.

  Please do not disassemble this engine or any other item supplied. You will breach your
warranty agreement and you will find it is a precision assembly which you will be unlikely to
re-assemble without considerable difficulty and specialist equipment. Simply slackening the
spinner nut of the rotor will immediately lose the delicate balance condition, without which
the engine may not run without damage to its rotating assembly.

  This warranty is void if any one or more of the following conditions applies. In such a case
Jets Munt will accept no responsibility for any damage or any other consequence caused by
the VT80 operation.

1. The product has been subject to any form of operation whilst containing incorrect fuel,
oil, or fuel/oil mix.

2. The product is crash damaged, pump is blocked due dirt ingestion, electronics or pump 
are flooded by fuel, connection leads are cut or lost its isolation and short-circuit, reverse
polarity on battery, etc.

3. Unauthorized maintenance or modifications have been made to any part of the product,
including the unlocking of the ecu and changing the manufacturer settings or any of the
items supplied has been dissasembled.

4. Parts have been damaged by ingestion of foreign objects (e.g. wires, sand, water etc).

5. The engine has been operated incorrectly. 

6. The product has been misused, neglected or inadequately maintained.

7. Damage to the engine where blockages in the fuel system have occurred by unfiltered or
contaminated fuel. 

Jets-Munt Representatives:

Check the current dealer list on our web page, www.jetsmunt.com 

Содержание VT80BL
























Отзывы: