background image

 

26.  Turn off the machine before cleaning. Use a brush or compressed air to remove chips or debris — do 

not use your hands. 

27.  Do not stand on the machine. Serious injury could occur if the machine tips over. 

28.  Never leave the machine running unattended. Turn the power off and do not leave the machine until it 

comes to a complete stop. 

29.  Remove loose items and unnecessary work pieces from the area before starting the machine. 

 

 

 

 

 

Familiarize yourself with the following safety notices used in this manual: 

 

 This  means  that  if  precautions  are  not  heeded,  it  may  result  in  minor  injury  and/or 

possible machine damage. 

 This means that if precautions are not heeded, it may result in serious injury or possibly 

even death. 

 

 
 
 

 

 

 

 

 

 

 

 

 

 

WARNING:

 Drilling, sawing, sanding or machining wood products generates wood dust and other 

substances known to the State of California to cause cancer. Avoid inhaling dust generated from wood 
products or use a dust mask or other safeguards for personal protection. 

Wood  products  emit  chemicals  known  to  the  State  of  California  to  cause  birth  defects  or  other 
reproductive harm. For more information go to http://www.p65warnings.ca.gov/wood. 

 

WARNING:

 This product can expose you to chemicals including lead which is known to the State of 

California  to  cause  cancer  and  birth  defects  or  other  reproductive  harm.  For  more  information  go  to 
http://www.p65warnings.ca.gov. 

Содержание XACTA Fence II Homeshop 30/52

















Отзывы: