background image

 

Familiarize yourself with the following safety notices used in this manual. 

 This means that if precautions are not heeded, it may result in minor injury and/or 

possible machine damage. 
 

 This means that if precautions are not heeded, it may result in serious or even fatal 

injury. 
 

 

 

 

4.0

  About this manual 

This manual is provided by JET covering the safe operation and maintenance procedures for a JET model 
SBR-30M and SBR-40M Shear, Brake and Roll. This manual contains instructions on installation, safety 
precautions, general operating procedures, maintenance instructions and parts breakdown. Your machine has 
been designed and constructed to provide consistent, long-term operation if used in accordance with the 
instructions as set forth in this document.  

If there are questions or comments, please contact your local supplier or JET. JET can also be reached at our 
web site: www.jettools.com. 

Retain this manual for future reference. If the machine transfers ownership, the manual should accompany it. 

 

 

Read and understand the entire contents of this manual before attempting set-up or 

operation.  Failure to comply may cause serious injury. 

 

 

Содержание SBR-30M





















Отзывы: