Jet JWP-208 Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 36

background image

5

Safety Decals

Familiarize yourself with the location and content of these decals on your planer.

!

1.      Read instruction manual before operating machine.
2.       Do not operate without all guards properly installed.
3.      Remove or fasten loose articles of clothing such as neckties, etc.
       Contain long hair.
4.      Remove jewelry such as finger rings, watches, bracelets, etc.
5.      Use approved safety glasses and/or face shield to protect eyes, and
          use other personal safety equipment as required.   Do not wear
       gloves.

6.      Disconnect machine from power source before making any
           adjustments or cleaning chips away from machine.
7.      Keep the floor around machine clean and free from scraps,
           sawdust, oil and grease to minimize the danger of slipping.
8.       Do not operate this machine while under the influence of alcohol
       or drugs.
9.      Failure to comply with these warnings may result in serious
       personal injury.

DO NOT REMOVE OR OBSCURE THIS LABEL

Fig. 1

«
...
3
4
5
6
7
...
»

Содержание JWP-208





































Отзывы:

Нет отзывов

Похожие инструкции для JWP-208

Бренд: Cambridge Audio Страницы: 2

Бренд: Cambridge Audio Страницы: 4

Бренд: Cambridge Audio Страницы: 84

CD5I - MANUAL 2

Бренд: NAIM Страницы: 4

AZ7333 - Cd Personal

Бренд: Magnavox Страницы: 27

Бренд: Aiwa Страницы: 2

Бренд: MAJORITY Страницы: 16

Бренд: Roadstar Страницы: 12

Бренд: Jensen Страницы: 12

Бренд: LEXIBOOK Страницы: 12

Бренд: Sony Страницы: 2

CDP-CE275 - Carousel Cd Player 5 Discs

Бренд: Sony Страницы: 2

CDP-C9ESD - Es Compact Disc Player

Бренд: Sony Страницы: 1

CDP-CE275 - Carousel Cd Player 5 Discs

Бренд: Sony Страницы: 18

Бренд: Sony Страницы: 24

Бренд: Sony Страницы: 20

Бренд: Sony Страницы: 24

CDP-CE405 - 5 Disc Cd Changer

Бренд: Sony Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды