4
Always wear the approved working outfit
- safety goggles
- ear protection
- dust protection
Do
not
wear gloves while operating this
machine.
For the safe handling of saw blades wear
work gloves.
Observe the chapter “save operation” in
this manual.
Control the stopping time of the machine,
it may not be longer than 10 seconds.
Insure that the workpiece does not roll
when cutting round pieces.
Use suitable table extensions and
supporting aids for difficult to handle
workpieces.
Always lower the blade guide close to the
workpiece.
With the machine table is inclined use the
fence and position it on the bottom side
only.
Always hold and guide the workpieces
safely during machining.
Remove cut and jammed workpieces only
when motor is turned off and the machine
is at a complete standstill.
Install the machine so that there is
sufficient space for safe operation and
workpiece handling.
Keep work area well lighted.
The machine is designed to operate in
closed rooms and must be placed stable
on firm and levelled ground.
Make sure that the power cord does not
impede work and cause people to trip.
Keep the floor around the machine clean
and free of scrap material, oil and grease.
Stay alert!
Give your work undivided attention. Use
common sense.
Keep an ergonomic body position.
Maintain a balanced stance at all times.
Do not operate the machine
when you are tired.
Do not operate the machine under the
influence of drugs, alcohol or any
medication. Be aware that medication can
change your behaviour.
Keep children and visitors a safe distance
from the work area.
Never reach into the machine while it is
operating or running down.
Never leave a running machine
unattended. Before you leave the
workplace switch off the machine.
Do not operate the electric tool near
inflammable liquids or gases.
Observe the fire fighting and fire alert
options, for example the fire extinguisher
operation and place.
Do not use the machine in a dump
environment and do not expose it to rain.
Wood dust is explosive and can also
represent a risk to health.
Dust form some tropical woods in
particular, and from hardwoods like beach
and oak, is classified as a carcinogenic
substance.
Always use a suitable dust extraction
device
Before machining, remove any nails and
other foreign bodies from the workpiece.
Use a push block when working the ends
of narrow stock.
Always store the push stick or the push
wood handle with the machine, also when
not in use.
Specifications regarding the maximum or
minimum size of the workpiece must be
observed.
Do not remove chips and workpiece parts
until the machine is at a complete
standstill.
Never operate with the guards not in
place – serious risk of injury!
Do not stand on the machine.
Connection and repair work on the
electrical installation may be carried out
by a qualified electrician only.
Have a damaged or worn cord replaced
immediately.
Make all machine adjustments
or maintenance with the machine
unplugged from the power source.
Remove defective saw blades
immediately.
3.3 Remaining hazards
When using the machine according to
regulations some remaining hazards may
still exist
The moving saw blade in the work area
can cause injury.
Broken saw blades can cause injuries.
Thrown workpieces can lead to injury
Wood chips and sawdust can be health
hazards. Be sure to wear personal
protection gear such as safety goggles ear-
and dust protection.
Use a suitable dust exhaust system.
The use of incorrect mains supply or a
damaged power cord can lead to injuries
caused by electricity.
4. Machine specifications
4.1 Technical data
Wheel diameter
Ø 240 mm
Cutting width
max 230 mm
Cutting height
max 80 mm
Sawblade length
1575 mm
Blade width
3 - 10 mm
Blade thickness
0,3 – 0,4 mm
Cutting speed
660 m/min
Machine Table(Lx W)
300x300 mm
Table tilting range
0° to 45°
Table above floor
330mm
Dust port
Ø 53mm
Overall Lx Bx H
395x 520x 754mm
Weight
20 kg
Mains
230V ~1/N/PE 50Hz
Output power
350W, S1
Reference current
1.6 A
Extension cord (H07RN-F):
3x1.5mm²
Installation fuse protection10 A Machine
lamp halogen 12V 21W
4.2 Noise emission
(Inspection tolerance 4 dB)
Workpiece beech:20mm
Acoustic power level
(according to EN ISO 3746):
Idling
LwA 80 dB(A)
Operating
LwA 93,6 dB(A)
Acoustic pressure level
(EN ISO 11202):
Idling
LpA 74,7 dB(A)
Operating
LpA 87,2 dB(A)
The specified values are emission levels
and are not necessarily to be seen as safe
operating levels. This information is
intended to allow the user to make a
better estimation of the hazards and risks
involved.
4.3 Content of delivery
machine table
Fence
Mitre gauge
Machine lamp
Dust port adapter Ø 57mm
Assembly bag Saw
blade Additional support
Operating manual
Spare parts list
