Jet JWBS-16 Скачать руководство пользователя | Manualshive

Страница: 5 / 30

background image

5

230 Volt Operation

If 230V, single phase operation is desired, the following instructions must be followed:

1. Disconnect the machine from the power source.

2. This bandsaw is supplied with four motor leads that are connected for 115V operation, as shown in

Figure A. Reconnect these four motor leads for 230V operation, as shown in Figure B.

3. The 115V attachment plug supplied with the bandsaw must be replaced with a UL/CSA listed plug

suitable for 230V operation.

Contact your local Authorized JET Service Center or qualified

electrician for proper procedures to install the plug. The bandsaw must comply with all local and
national codes after the 230V plug is installed.

4. The bandsaw with a 230V plug should only be connected to an outlet having the same configuration.

No adapter is available or should be used with the 230V plug.

Important: In all cases (115 or 230 volts), make certain the receptacle in question is properly
grounded. If you are not sure, have a registered electrician check the receptacle.

«
...
3
4
5
6
7
...
»

Содержание JWBS-16































Отзывы:

Нет отзывов

Похожие инструкции для JWBS-16

Бренд: KAKA Industrial Страницы: 25

Бренд: Tre Spade Страницы: 97

Бренд: Spitznas Страницы: 18

Бренд: MachineryHouse Страницы: 11

Бренд: BN Products Страницы: 8

Бренд: Carbatec Страницы: 30

Бренд: RIDGID Страницы: 120

Бренд: Cantek Страницы: 26

Бренд: Wood-mizer Страницы: 158

Бренд: Craftsman Страницы: 8

Бренд: Craftsman Страницы: 18

21419 - 9 in. Band Saw

Бренд: Craftsman Страницы: 24

Бренд: Craftsman Страницы: 32

Бренд: Craftsman Страницы: 28

21828 - Professional 10 in. Jobsite Saw

Бренд: Craftsman Страницы: 46

21833 - Professional Contractor Table Saw

Бренд: Craftsman Страницы: 29

Бренд: Craftsman Страницы: 30

Бренд: Craftsman Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды