3
29. Keep hands out of the line of saw blade.
30. Don’t use in dangerous environment. Don’t use
power tools in damp or wet location, or expose
them to rain. Keep work area well lighted.
1.2
Miter saw safety warnings
Specific safety instructions for this compound miter
saw:
31. Do not operate the miter saw until it is
completely assembled and installed according
to these instructions.
32. If you are not familiar with the operation of miter
saws, seek guidance from your supervisor,
instructor or other qualified person.
33. Always hold the work firmly against the fence
and table.
34. Do not perform free-hand operations; use
clamp wherever possible.
35. Keep hands out of the path of the saw blade. If
the workpiece you are cutting would cause your
hands to be within 8 inches of the saw blade,
the workpiece should be clamped in place
before making the cut.
36. Be sure the blade is sharp, runs freely and is
free of vibration.
37. Allow the motor to come up to full speed before
starting a cut.
38. Keep the motor air vents clean and free of chips
or dust.
39. Make sure all handles are tight before cutting,
even if table is positioned in one of the positive
stops.
40. Be sure both the blade and the flange are clean
and the arbor bolt is tightened securely.
41. Use only blade flanges specified for your saw.
42. Never use blades larger in diameter than the
size specified by your particular model.
43. Never apply lubricants to the blade when it is
running.
44. Always check the blade for cracks or damage
before operation. Replace a cracked or
damaged blade immediately.
45. Never use blades rated for fewer RPM’s than
the rated speed of the saw. See your saw
specifications.
46. Always keep blade guards in place and use at
all times.
47. Never reach around the saw blade.
48. Make sure the blade is not contacting the
workpiece before the switch is turned ON.
49. After completing the cut, release the trigger and
wait for the blade to stop before returning the
saw to raised position.
50. Make sure the blade has come to a complete
stop before removing or securing the
workpiece, changing the workpiece angle or
changing the angle of the blade.
51. Never cut metals or masonry products with this
tool. This miter saw is designed for use on wood
and wood-like products.
52. Never cut small pieces. If the workpiece being
cut would cause your hand or fingers to be
within 8 inches of the saw blade, the workpiece
is too small.
53. Provide adequate support to the sides of the
saw table for long work pieces.
54. Never use the miter saw in an area with
flammable liquids or gases.
55. Never use solvents to clean plastic parts.
Solvents could possibly dissolve or otherwise
damage the material.
56. Shut off the power before servicing or adjusting
the tool.
57. Disconnect the saw from the power source and
clean the machine when finished using.
58. Make sure the work area is clean before leaving
the machine.
59. Should any part of your miter saw be missing,
damaged, or fail in any way, or any electrical
component fail to perform properly, remove the
plug from the power supply outlet. Replace
missing, damaged, or failed parts before
resuming operation.
WARNING:
This product can expose you to
chemicals including lead and cadmium which
are known to the State of California to cause
cancer and birth defects or other reproductive
harm, and phthalates which are known to the
State of California to cause birth defects or other
reproductive harm. For more information go to
http://www.p65warnings.ca.gov.
WARNING:
Drilling, sawing, sanding or
machining wood products generates wood dust
and other substances known to the State of
California to cause cancer. Avoid inhaling dust
generated from wood products or use a dust
mask or other safeguards for personal
protection.
Wood products emit chemicals known to the
State of California to cause birth defects or other
reproductive harm. For more information go to
http://www.p65warnings.ca.gov/wood.
Содержание JMS-10X
