background image

 

15

5.  Using a machinist’s square, check to make 

sure the table is 90 degrees to the blade. 
USING LEATHER PROTECTIVE GLOVES, 
turn the upper drive wheel to check the 
squareness at a minimum of three points on 
the blade 

6.  If the table is not level, unlock the lock nut on 

the table leveling bolt. 

7.  Turn the leveling bolt as required to make the 

table square to the blade. 

8.  Lock the leveling bolt lock nut and recheck the 

table level. When the table is level. 

9.  Lock the table lock knobs securely and 

recheck for level.  Adjust as necessary until 
the table is level while everything is tightened 
to working tightness. 

10. With everything is locked down, look at the 

pointer for the angle gauge. It should be 
exactly on the zero mark of the gauge (Figure 
13). If not, loosen the pointer screw, adjust the 
pointer until it is on zero, then tighten the 
pointer screw while holding the pointer 
securely in position on zero. 

Adjusting Miter Gauge Slot 
Parallelism 

The miter slot should be parallel to the side of the 
blade. If the saw is not cutting straight when using 
the miter gauge, the miter slot may not be parallel. 

1.  Put a straight edge against the blade. Make 

sure to position the blade so tooth offset does 
not affect the straight edge. 

2.  Measure from both ends of the miter slot to the 

straight edge. 

3.  If the measurements are not equal at both 

ends of the slot, loosen six bolts securing the 
table to the table trunnions (see Figures 13 
and 14.) 

4.  Adjust the table until it is parallel with the 

blade. 

5.  Tighten the trunnion attaching bolts. 

Adjusting Blade Speed (Models J-
8201/J-8203) 

Figure 7 

provides blade speeds for various 

materials. To adjust the blade speed, change the 
clutch position of the clutch (in or out) and the 
position of the drive belt on the pulleys on the 
motor and reduction gearbox shafts. 

Adjusting Blade Speed (Models J-
8201VS/J-8203VS)  

See Figure 10. 

1. The blade speed is controlled by an 

adjustment mechanism on the right end of the 

saw. Speed increases or decreases as the 
knob is turned. 

2.  A placard on the drive belt guard (shown 

below) provides recommended speeds for 
various materials.  

3.  A speed indicator is provided on the barrel of 

the adjustment mechanism. In surface feet per 
minute; Position 0 = 334, 1 = 262, 2 = 216, 3 
=171, 4 = 137, and 5 = 116. 

4.  Turn the speed adjustment knob to the desired 

setting as determined by the material being 
cut. 

 

Figure 10: Variable Speed Control 

Changing Clutch Position 

WARNING: NEVER attempt to shift the clutch 
mechanism while the saw is running. The saw 
must be turned off before clutch is shifted. 

1.  Turn the main switch to off. 

2.  Pull the door open on the pulley case. 

3.  Turn the clutch handle clockwise and push in, 

to engage the high speed pulley drive. Or, turn 
the clutch handle clockwise, and pull out, to 
engage the reduction gearbox drive. 

NOTE:

 When pushing or pulling the clutch 

knob, the dogs on the clutch mechanism are 
being engaged. Take the time to make sure 
the clutch handle is all the way in, or all the 

Содержание J-8201





































Отзывы: