jenway 7310 Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 86

jenway 7310 Скачать руководство пользователя страница 49

51

SECTION 10 – Saving, Printing and Autologging

The utility toolbar in the expanded operating menu provides access to printing, print setup options,
opening, saving and deleting results and methods and autologging options.

If the method lock has been activated the method selection menu is disabled.

Fig 10.1 - Expanded Operating Menu

10.1

SAVING METHODS

Up to 48 methods can be saved in each of the measurement modes to the internal memory of the
instrument. Once the method has been saved to the internal memory the method can be saved directly
to a USB memory stick and opened on another instrument.

10.1.1 SAVING METHODS TO INTERNAL MEMORY

In the expanded operating menu press the key adjacent
to the

method

icon to open the method selection menu.

Select the location to save the method by pressing the key
adjacent to the location. Use the keys below the

arrow

icons to move page up or down. Press the key below the

create method

icon to open the method naming menu.

The default method name will be displayed. To save the
method under the default name press the key adjacent
to the

tick

icon. To change the name of the method press

the key below the

eraser

icon. One press of the key will

delete one letter, holding the key for 2 seconds will delete
the name completely.

To select letters use the keys adjacent to the

arrow

icons to move around the menu. Once the required

letter is highlighted press the key below the

pencil

icon to select the letter. Up to eight characters can

be selected. To change the letter case or to use numbers in the method name press the key below the

AB

icon. Repeat pressing of this key will cycle between upper case, lower case and numbers. Once the

required name for the method has been entered press the key adjacent to the

tick

icon to save the

method and return to the method selection menu.

If there is already a method saved in the chosen location
confirmation will be needed to replace the existing
method with the new one; press the key adjacent to the

tick

icon to confirm replacement. Press the key adjacent

to the

cross

icon to cancel and return to the method

naming menu. To exit the method naming menu without
saving the method press the

back

key.

0.000

0.000

400

09:02

ppm

ABS

nm

01

02

03

04

TEST

05

06

07

08

TEST

A B C D E F G H I
J K L M N O P Q R
S

T

U V W X Y Z _

01: TEST

01: EXP_1 ?

Print/print settings
Results selection menu
Method selection menu
Autolog menu

«
...
47
48
49
50
51
...
»

Содержание 7310























































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды