jenway 7310 Скачать руководство пользователя страница 22

Страница: 22 / 86

The time set will begin to count down when there is
no lamp activity. When the count down is complete the
lamp and the fan will be turned off and the

lamp save

icon is shown in all the measurement modes. To bring
the instrument out of the lamp save in order to perform
a measurement press the key below the

lamp save

icon.

The lamp and fan will be turned back on and the lamp
will begin to warm up.

The

lamp cold

icon is displayed adjacent to the

calibrate

to zero

icon in the measurement mode. The time needed

for the lamp to warm up is five minutes.

To view the remaining warm up time press the key below
the

lamp cold

icon. Calibration and measurements can

be performed whilst the lamp is warming up but these
results may not be accurate.

Once the warm up time of five minutes is complete the

lamp cold

icon disappears.

0.000

100.0

400

0 9 : 0 2

ABS

0.000

100.0

400

09:02

ABS

09:02

16:30

0.000

100.0

400

09:02

ABS

Содержание 7310























































































Результаты поиска

Содержание 7310

Отзывы:

Бренды по названию

Популярные бренды

jenway 7310, Руководство по эксплуатации

Результаты поиска

Содержание 7310

Отзывы:

Бренды по названию

Популярные бренды