background image

                    PowerPlus Amplifiers

13

Troubleshooting

NOTE: If the protection light is activated with no speakers connected to 
the amplifier, and all the power connections are correct, this would 
indicate an internal problem with the amplifier.

Problem

Possible Cause

Corrective Action

Amplifier does not 
turn on

No power to +12V 
terminal

Check fuse(s)

No power to REM 
terminal

Check head unit fuse(s) and 
wiring

Blown main fuse at 
battery

Replace fuse and identify 
cause of failure

Blown fuse at amplifier

Replace fuse and identify 
cause of failure

Faulty ground

Re-ground main power 
ground to bare metal 
chassis

Volume control too 
sensitive

Input level control 
adjusted too high

Re-adjust the input level 
(refer to page 8)

Distorted sound

Input level control 
adjusted too high

Re-adjust the input level 
(refer to page 8)

Blows fuse(s) at amp Power wires connected 

backwards

Reconnect power wires 
properly

Internal problem with 
amp

Take unit for service

Engine noise / 
Alternator whine

Ground loop(s)

Use good quality shielded 
RCA cables

Faulty ground at amp

Re-ground amp to clean 
bare metal chassis

Faulty ground at head 
unit

Re-ground head unit to 
clean bare metal chassis

Inductive coupling

Re-route RCA and/or 
speaker wires away from 
factory harnesses

Input level on amp set 
too high

Re-adjust input level (refer 
to page 8)

Thermal protection 
activated

Amplifier driving 2 ohm 
load for long durations

If the amplifier “thermals” 
frequently while driving 
subwoofers, install fan to 
keep amp cool.

Short circuit 
protection activated

Blown speakers

Check all speakers

Speaker wire(s) shorting 
to ground

Check for faulty wiring

Defective crossover

Faulty passive crossover

Low impedance 
protection activated

Amp connected to 
improper load

Check speaker connections

Amp will not drive a 1 
ohm mono load, 2 ohm 
minimum in mono 
configuration

Verify that speakers are 
connected properly

Speakers defective/
blown

Check speakers

Faulty passive 
crossovers

Check crossovers

Poor bass response

Speakers out of phase

Check speaker polarity; 
reverse the connection to 
one speaker only if two 
subwoofers are connected 
to the amplifier.

Содержание PowerPlus 900















Отзывы: