11
ALARM OPERATIONS
Setting the Alarm time
When the unit is at the standby mode :
1. Press the
MODE
button once , the alarm hour digits blink.
2. To set hour, turn the
VOLUME
wheel to obtain a desired value.
3. Press the
MODE
button again , the alarm minute digits blink.
4. To set minute, turn the
VOLUME
wheel to obtain a desired value.
Select wake up alarm source
5. When either the alarm hour or minute digits blink, each press of the
FUNCTION
button allows you to
select Buzzer , iPod/iPhone or Radio as the alarm source where the corresponding indicator "Alm ",
"Alm iPod/iPhone" or "AlmRad" displays on screen.
Note :
- If "Wake to iPod/iPhone " is selected but your iPod/iPhone has not been docked, the alarm source
will be redirected to the Alarm Buzzer automatically when the alarm time is reached.
- When "Wake to Radio" is selected, make sure the radio staion you want to wake to is tuned.
6. To save all settings and exit the setting mode, press the
SNOOZE
button.
7. To activate the daily alarm, press the
ALARM ON/OFF
button and the corresponding alarm source indicator
appears on LCD display.
Wake to Buzzer
* When the alarm time is reached, the buzzer alarm will sound for one minute.
* It goes into Auto Snooze mode if no button has been pressed. The display shows the
“
SNOOZE
”
indicator. The buzzer turns off for the snooze time (around 10 minutes) then comes on again.
This operation will be repeated three times. After the fourth alarm is finished, the alarm will shut
off until the same alarm time on the next day.
* You may also activate the snooze function manually after the alarm sounds by pressing the
SNOOZE
button. The buzzer stops for the snooze time then comes again.
* To cancel the snooze before it expires, press the
POWER
button once.
* The snooze operation (including auto snooze and manual snooze) can be repeated by 3 times only.
* To stop the alarm immediately after the buzzer sounds, you can also press the
ALARM
ON/OFF
button.
It resets itself for the following day.
Wake to iPod/iPhone or Radio
* When the alarm time is reached, the selected alarm source (iPod/iPhone or Radio) will automatically turn on.
It starts softly and gradually becomes louder.
* It plays for 60 minutes then shuts off and resets itself for the following day.
* During the activation of the alarm source, you may press the
SNOOZE
button to activate the
snooze function. The alarm stops for the snooze time (around 10 minutes) then turns on again.
* To cancel the snooze before it expires, press the
POWER
button once.
* This manual snooze operation can be repeated three times. Each time the alarm turns on, it plays
for 60 minutes (without pressing the snooze button).
* To stop the alarm immediately after the alarm sounds, you may also press the
ALARM
button.
It resets itself for the following day.
Note :
- For the alarm source iPod/iPhone is selected and the corresponding device has not been docked
in the station. When the alarm comes, it will redirect to
“
Wake to Buzzer
”
automatically.
12
AUXILIARY INPUT
This unit provides an auxiliary audio signal input for
Connect the other end of the cable to a Line Out Jack or Headphone Jack of your non-dockable MP3 player,
CD player and older, non-dockable iPods (except 3rd gen iPod shuffle) then listen to your external source
through the speakers of this system.
1.
with 3.5 mm stereo plug to the
AUX IN Jack
located at rear of the unit.
2. Connect the other end of the cable to a Line Out Jack or Headphone Jack of your external audio device.
3. Turn on the external audio device.
4. To select auxiliary audio input, press the
FUNCTION
button until the AUX indicator is displayed on the LCD.
5. The volume level can now be controlled through the main unit. Operate all other functions on the auxiliary
device as usual.
Note:
(1) If you're connected the Line Out Jack of your external device then you only need to adjust the volume
control of this unit. If you're connected the Headphone Jack of your external device, then you may need to
adjust both the volume control of your external device and the volume control of this unit to find the most
desirable volume setting.
connecting external audio devices.
Use an audio cable with 3.5 mm stereo plug to connect the external device to the AUX IN Jack
located on the back of the unit.
Connect the audio cable
(2) Press the
POWER
button turning off the unit when you finish listening.
Don't forget to switch off the power of your external device as well.
CLOCK SETTING
When the unit is OFF( power off mode) :
Set Clock
1. Press the
MODE
button 3 times, the hour digits blink.
2. To set hour, turn the
VOLUME
wheel to obtain a desired value.
Note
: Make sure the hour is set so that the
AM
or
PM
indicators are displayed correctly.
3. Press the
MODE
button again, the minute digits blink.
4. To set minute, turn the
VOLUME
wheel to obtain a desired value.
Set 12/24 Hour format
5. Press the
MODE
button repeatedly to enter 12/24 hour format setting mode, "H12" appears and flashing.
6. To select H12 (12Hour) or H24 (24 Hour) format, rotate the
VOLUME
wheel.
Exit setting mode
7. To save all settings and exit the setting mode, press the
SNOOZE
button.
