6
7.
To disable ALARM 1 (or 2) from automatically sounding on the upcoming days, press and hold the AL1 (or AL2)
button for about 2 seconds, the corresponding AL1 (or AL2) INDICATOR will go off.
8.
To resume ALARM 1 (or 2) from automatically sounding on the upcoming days, press and hold the AL1 (or AL2)
button for about 2 seconds, the corresponding AL1 (or AL2) INDICATOR will turn on and the alarm(s) will sound
the following day at the set time.
TURNING OFF THE ALARM
When the preset alarm time is reached, the AL1 (or AL2) INDICATOR will flash on the LCD DISPLAY and the beeper
alarm or radio will sound for 30 minutes unless interrupted by pressing SNOOZE. To stop the alarm immediately, tap
the corresponding AL1 (or AL2) button or POWER ON/STANDBY
button. The alarm will ring again at the same
alarm time on the following day, or when set to go off based on your Alarm settings.
SNOOZE FUNCTION
When the alarm source is sounding, press the SNOOZE button to suspend the alarm and activate the snooze
function. The Alarm will temporarily stop and sound again 9 minutes later but the AL1 (or AL2) indicator will keep
flashing.
Notes:
This manual snooze operation can be repeated again and again.
To turn off the snooze function before it ends, tap the corresponding AL1 (or AL2) button or the
button. The
AL1 (or AL2) INDICATOR will stop flashing.
LISTENING TO THE RADIO
RADIO TUNING
1.
In standby mode, tap the POWER ON/STANDBY
button to turn the unit
‘On’.
2.
Tap the AM/FM button repeatedly to select the AM or FM band. The corresponding indicator will light up.
3.
The LCD DISPLAY will show the radio frequency for about 5 seconds and then revert to normal time display.
AUTOMATIC SEARCH FOR RADIO STATIONS
To automatically search for stations with strong signals, press and hold the TUNE UP
or DOWN
button until the
frequency readout on the display begins to scan. Release the button. The tuner will stop on the first strong station it
finds.
MANUAL SEARCH FOR RADIO STATIONS
1.
Tap the
or
button repeatedly to choose your desired radio station.
2.
Tap the VOLUME UP
+
or DOWN
-
button to set the desired volume level. The volume level reading will
appear in the LCD DISPLAY.
Notes:
Use manual tuning to select weaker stations that might be skipped during automatic tuning.
If the automatic tuning does not stop on the exact frequency of the station, for example, it stops on 88.9 MHz
instead of 88.8 MHz, use
the manual tuning method to “fine tune” to the exact frequency of the desired station.
HINTS FOR BEST RECEPTION
AM - The AM antenna is located inside the cabinet of the unit. If AM reception is weak, change the position of unit until
the internal antenna picks up the strongest signal.
FM - To insure maximum FM tuner reception, unwrap and fully extend the EXTERNAL FM WIRE ANTENNA for best
FM radio reception.
TO SET/RECALL RADIO STATION PRESETS
1.
After selecting the desired radio band, press the
or
button to select the desired radio station.
2.
Press and hold the SET MEM button, the next available preset memory number will flash on the LCD display.
(Note: “P01” will flash in the display if you are programming presets for the first time.)
3.
Press the
or
button to change to the desired preset number P01 thru P10.
4.
Repeat steps #1 thru #3 to preset up to 10 FM stations in FM mode and 10 AM stations in AM mode.
5.
To recall one of the preset stations already programmed, tap the M+ button repeatedly until you reach the desired
preset number/radio station.
SLEEP TIMER OPERATION
The sleep timer allows you to turn the unit off after a designated time has elapsed.
1.
While listening to the radio, tap the SLEEP button and sleep time
‘90’ (minutes) appears in the LCD DISPLAY.
2.
Repeatedly tap the SLEEP button to select a sleep timer of 90, 60, 30 or 15 minutes. Wait for about 10 seconds
Содержание JCR-232
Страница 10: ...9 0314 Printed in China ...
