background image

JCDWIN

6

Display Selector (DISP)

This unit can display either the clock time or radio frequency/CD player functions. Press the 

DISP

 button (6) on the control panel or remote control to display the time for approximately 5 

seconds. The correct time of day can be set by pressing and holding the 

DISP

 button.

Setting the Clock

To set the clock, perform the following steps:
1.

Press the 

DISP

 button (6) to display the clock.

2.

Press and hold the 

DISP

 button (6) until the time display flashes.

3.

Within 5 seconds, press the 

TUNE

 down button (18) to adjust the minutes to the desired 

setting.

4.

Press the 

TUNE

 up button (19) to adjust the hour.

5.

Press the 

DISP

 button again to return to radio frequency or disc play or wait five seconds 

and normal operation will resume automatically.

Preset Equalizer (PEQ)

The preset equalizer applies preset sound effects to the unit’s audio output signal. To adjust 
the preset equalizer, press the 

PEQ

 button (23) on the remote control. Press repeatedly to 

choose between the following modes: “FLAT”, “CLASSICS”, “POP M”, “ROCK M” or “DSP 
OFF”.

TUNER OPERATION

Select a Band

Press the 

BAND 

button

 

(21) on the control panel (or 

BND

 on the remote control) to change 

between three FM bands and one AM band. Each band stores up to six preset stations. 

Tuning

Auto Seek Tuning

Press the 

TUNE

 up (19) or 

TUNE

 down button (18) on the control panel (or 

U

 and 

D

 on the 

remote control) for less than three seconds to move to the next station automatically.

Manual Tuning

Press the 

TUNE

 up (19) or 

TUNE

 down button (18) for more than three seconds to enter 

manual tuning mode. Press the 

TUNE

 up or 

TUNE

 down button to change the radio frequency 

number up or down one step. 

Scan

Press the 

SCAN

 button (22) on the control panel (or 

SCN

 on the remote control) to 

automatically search for stations. Each available station will flash on the display for a few 
seconds before the next is searched. To select a “flashing” station, press the 

SCAN

 button 

again.

Preset Stations

Six numbered preset buttons store and recall stations for each band.

Store a Station

Select a band (if needed), then select a station. Hold a preset button (9-14) for three seconds. 
The preset number will appear in the display.

Recall a Station

Select a band (if needed). Press a preset button (9-14) to select the corresponding stored 
station.

1

4

6

5

2

3

8

10

16

9

11

12

13

14

21

15

20

19

18

7

22

17

Содержание JCDWIN











Отзывы: