RTR-
500
A
1
/A
2
External Power Adaptor
About this Product
This product is an External Power Adaptor especially designed for use with our
RTR-
500
x Series data loggers.
Caution
: If this product is used in combination with any product other than those
specified above, T&D Corporation shall in no manner, whatsoever, guar-
antee the operation of this product.
Package Contents
The package contains the following:
External Power Adaptor
Rubber Packing
AC Adaptor
*
1
Rubber Packing(small)
(for AC adaptor jack)
Attachment hook
Drying agent
(Silica Gel)
Double-sided Adhesive Tape
×
1
(for fastening silica gel)
Screws
×
2
(extras for fastening back of
main unit)
Specifications
Voltage Input
：
DC
6
V
Back-up Power
*
2
：
Ni-MH Battery (In case of power loss)
(Internal)
Back-up Time
：
4
days
*
3
Charging Method
：
Trickle Charge
Operating Temperature
：
0
-
60
ºC
Waterproof Capability
：
None
Weight
：
about
37
g (without AC adaptor)
Note
:
*
1
: An AC adaptor is not included in the RTR-
500
A
2
packages. For details about
purchasing, contact you local distributor.
*
2
: If the Back-up Power function is on, the RTR-
500
x Series LCD display will show
or
.
*
3
: Battery Life varies depending on measuring environment, recording interval,
transmission frequency, and ambient temperature. The battery life estimated
here is calculated using a new battery under normal operating conditions and in
no way should be understood as a guarantee of battery life.
Caution
:
If you do not wish to lose the recorded data, please finish this operation in less than
1
minute from the time that you remove the battery from the RTR-
500
x Series unit. (We
suggest that you download recorded data before attaching the adaptor. For details about
downloading data, see the User
’
s Manual that comes with the software you are using
or the Base Unit being used for our Thermo Recorder RTR-
500
x Series Data Loggers.)
1
.
Remove the back lid from the RTR-
500
x Series unit and take out the
battery.
2
.
Attach the double-sided adhesive tape to the back of the drying agent
and fix to the inner side of the RTR-
500
A
1
/A
2
.
3
.
Check the RTR-
500
A
1
/A
2
rubber packing for abrasions, cuts and dirt. If
the packing is in good condition, insert into the grooves making sure that
it is properly fit.
Caution
:
- Abrasions or dirt may cause small openings to occur through which water
or other foreign objects can enter and cause damage to the unit.
- The rubber packing is a special item and is not sold in stores. If it becomes
damaged, please replace it by ordering [Maintenance Set] (TR-
00
P
1
).
4
.
Making sure that the
2
electrical wires are in the grooves as in diagram
A (below left), insert A (as in right diagram) into the battery space of the
RTR-
500
x Series unit. Close the case and fasten the screws.
A
A
Caution
: If the electrical wires are not properly in their grooves, the lid may not
completely close. Please make sure that the wires are in their grooves
before continuing.
If no recording settings have been made before carrying out this operation, record-
ing will begin from the time section A is inserted into the battery space.
* If, after inserting section A, nothing appears in the unit's LCD display, please
repeat the steps above and attach again. For details about the display, see the ap-
propriate user's manual for the RTR-
500
x Series unit.
5
.
Attach the small rubber packing to the AC adaptor jack (as below) and
connect it to the main unit.
6
.
If necessary, put on the attachment hook.
7
.
Insert the AC adaptor plug into the electrical outlet.
2009
.
04
16004244220
2
nd Edition
User's Manual
Thank you for purchasing this product.
Carefully read and fully understand these
instructions before using this unit.
©
Copyright
2008
T&D Corporation. All right reserved.
How to Attach
Shimadachi
817
-
1
, Matsumoto, Nagano
390
-
0852
Japan
Tel:+
81
-
263
-
40
-
0131
Fax:+
81
-
263
-
40
-
3152
E-mail: [email protected]
Homepage: http://www.tandd.com/
