Jennings JSVG Series, Руководство пользователя

Страница: 2 / 3

KEY PAD FUNCTIONS
*
UNIT
Unit (mode) selection: Press and release the key once to change weight unit
You can select g (grams), oz (ounces), dwt (pennyweight), ozt (troy ounces), ct
(carats), gn (grains) or lb(pounds/mg(miligrams)
* PCS (Count) Sample sizes can be 25, 50, 75 or 100
The following steps outline the procedure for cummulative weighing of samples:
Switch the scale on, Place a 'given' number of samples of an item on the tray.
Press the [UNIT] key several times to put the scale in PCS mode (the indicator
should be on pcs). Select the sample size (the same as you chose above) by
pressing the [PCS] key (press it as many times as necessary to put it in the
correct sample size (the sample size is the same as in step three =10,20,50or
100), Press the [UNIT] key, the display will show "pass", then after 2 seconds,
the scale will remember the sample size you selected and show the starting
sample size on the display.(You can now remove the samples if you want to
return the scale to 0pcs). Place the items that you want counted onto the tray,
the total number of items will show on the display.Press the [UNIT] key to exit
the counting function and return to normal weighing mode
*
!
ON/OFF
Press this key to turn unit on. Once the unit is on, press and hold the same
key to turn the scale off
*
ZERO (TARE)
Press Zero to reset the scale to zero. This can be used for eliminating from a
sample (or a Tray/Container) the weight value of a container weight is
permanently removed for the remainder of the procedure. Just turn the scale
ON, place the tray or container on weighing platform, and press the ZERO key.
The scale will show 0.0 (or 0.00) on the display and you can add items to the
container/tray. NOTE: When all weight are removed from the weighing tray, the
tared value of a container will be displayed as a
negative number . Cycle the
power on the scale to reset the scale to zero.
* LIGHT
Press the center [Light] key to turn on the bright LCD backlight. It will stay on for
several seconds. Press this key again to turn off the backlight.
Selection of auto-power-off mode
Press and hold [UNIT] , then press [ON/OFF], The scale will enter the
function setting mode. The display will show A_ON or A_OFF, Press [ZERO]
, the display will show A_ON, this means auto- off function active. Press
[ZERO] again, the display will show A_OFF, (auto-off function inactive).
** These electronic scale are precision instruments. Avoid disturbing
environmental conditions such as currents, vibrations, strong electrical and
magnetic fields as well as a rapid change of the ambient temperature.
JSCALE JS-V (G/X) MANUAL
PLEASE READ COMPLETE INSTRUCTIONS BEFORE USE
Thank you for purchasing The Jennings JS-V. With normal care and proper
treatment it will provide years of reliable service. Please read all operating
instructions carefully. You can contact us at
www.Jscale.com
. KEEP THE FOLLOWING POINTS IN MIND:
* Avoid lengthy exposure to extreme heat or cold, your scale works best when
operated at normal room temperature.
If the scale has been subjected to
temperature change, please allow the scale to acclimate to normal room
temperature for at least one hour before use.
* Allow sufficient warm up time. Turn the scale On and wait several seconds to
give the internal components a chance to stabilize before weighing.
* The cleaner the environment the better. Dust, dirt, moisture, vibration, air
currents and proximity to other electronic equipment can all cause an adverse
effect on the reliability and accuracy of your scale.
* Handle with care. Gently apply all items to be weighed onto tray top. Although
this scale is designed to be quite durable, try to avoid rough treatment as this may
permanently damage the internal sensor and void your warranty.
* Avoid shaking, dropping or otherwise shocking the scale. This is a precision
instrument and MUST BE HANDLED WITH EXTREME CARE.
*
IMPORTANT ADVICE: Place the item to be weighed on the platform, after
the stable weight is displayed remove the item immediately. This will
prolong the longevity and accuracy of this weighing instrument.
.** These electronic scale are precision instruments. Do not operate near an in-
use cell phone, cordless phone, radio, computer or other electronic device.
These devices emit RF and can cause unstable scale readings. If your scale
ever performs poorly, try moving the scale to a different room or location.
This is a very precise scale - the display may seem to wander or jump when
weighing. This is due to air currents or vibrations. Stable weighing is achieved
when the display remains fixed for 3 seconds.
OPERATION_____________________________________________
Battery Operation:
1) Three “AAA” size ALKALINE batteries are required.
2) To install batteries:
a) Release the battery cover by sliding out-wards.
b) Place batteries into battery compartment aligned correctly.
c) Replace battery cover.
DO NOT USE EXCESSIVE FORCE & DO NOT PRESS ON THE TRAY!!!
3) The scale is now ready for battery operation.
(Advanced users only) CALIBRATION______________________________
IMPORTANT: This scale was professionally factory calibrated before shipment
and does NOT need to be recalibrated by the end user. However, if you wish to
recalibrate your scale we provide these instructions for calibration:
Repeat
calibration if the display locks on 8888, EEEE or LLLL. Incorrect calibration can
occur if you do not follow the steps exactly. If your scale does not perform
accurately, please try replacing your batteries before you calibrate. You will
need a calibration weight (see below) to calibrate this scale.
NOTE: if you do
not have access to a calibration weight you can purchase one at your local
store or in emergency situations you can use coins or weights (ie 2 US Nickels
= 10g) as a calibration weight
.
The JS-VG-10, requires a 10gram weight to calibrate
The JS-VG-20, requires a 20gram weight to calibrate
The JS-VG-40, requires a 40gram weight to calibrate
The JS-50XV, requires a 50gram weight to calibrate
The JS-100XV requires a 100gram weight to calibrate
1) Place the scale on a Flat, very stable surface and turn it ON
2) Press and hold the “ZERO” key for 5 seconds until the display
shows CAL - then release the key.
3) Press the ZERO key again, the display will flash CAL and then
10 (or 20/40/50/100 depending on model above)
4) Gently place the weight(s) on the tray and wait 3 seconds. The
display will show PASS and return to the weight value.
5) Calibration is complete, Remove the weight and turn the scale Off.
NOTE: if after calibration your scale does not read accurately, this indicates
calibration error and the calibration process should be repeated slower.
Please calibrate on a very stable flat surface
INACCURACY / ERROR___________________________________
The primary reasons for inaccuracy or malfunction are low batteries, incorrect
calibration, overload or operating on an unstable surface. Please keep this in
mind and maintain and operate your scale properly. The scale is a precise
instrument and must be handled with the upmost care and caution.
FEATURES_______________________________________________
Power Up Segment Test and Battery voltage:
When first turning the scale on, the display will show - - H I - - and then it may
(depending on model) show the battery voltage (ie bt=4.5). This display will
remain for approximately 2 seconds and then reset to 0.
Overload: When an applied load exceeds the capacity. “EEEE” will appear on
the display. Remove the excessive load immediately! Although the JS uses
proprietary overload protection technology, it is still possible to damage the
weighing sensors by overload.
!Remember: You can permanently damage the scale by overloading it!
The following features are optional and depend on the scale model;
* Weighmeter™:
On the side of the display you will notice a series of bars that increase as the
load on the scale increases. This is our Weighmeter™ invention. It helps you
know the remaining capacity on the scale and also will indicate an overload if
one occurs. Please use the Weighmeter™ to monitor your weighing loads and
please do not overload this scale.
*Timer function:
Begin with the scale OFF. Press [on/off] and hold the [PCS] key, until the
display shows "timer*" (*it will appear a bit strange because of the LCD
segments), press [PCS] the display will show "0.00.00", press [PCS] again, this
means that the timer function is active. Press [PCS],this means that the timer is
inactive. Press [zero], the display will show 0.00.00
*Clock function:
Begin with the scale OFF. Press [on/off] and hold [PCS] until the display shows
"timer*", press [unit] the display will show "time", then press [PCS] , the display
will show "00=00". Press [unit] to set the HOUR, press [zero] to set the minutes.
The clock function is now activated.
*Removable wind covers;
The JS-VG comes with two removable clear wind covers. They can be removed
only when the cover is completely open. Open the cover all the way and slide to
the side to remove or re-instal the cover. Be careful not to crush anything under
the cover onto the weighing tray (this can cause an accidental overload.