JENCO VisionPlus pH6175 Скачать руководство пользователя

Страница: 2 / 16

CONTENTS

GENERAL INTRODUCTION

…………………................2

INITIAL INSPECTION

……...………………....................2

POWER INPUT

…….……...………………......................2

INSTALLING THE BATTERIES..

…………....................3

DISPLAY & KEYS FUNCTIONS

…..……………..…...…..…3

A. Display

......................................................................3

B. Keys

...........................................................................4

OPERATIONAL PROCEDURES..

……..........................5

A. Buffer Set Selection

.....................................................5

B. pH Calibration

.............................................................6

a. Calibration with an ATC/Temp probe in the pH-AUTOLOCK

mode

........................................................................6

b. Calibration with manual temperature compensation in the

pH AUTOLOCK mode

....................................................7

c. Calibration with an ATC/Temp probe in the pH NON-

AUTOLOCK mode

........................................................8

d. Calibration with manual temperature compensation in the

pH NON-AUTOLOCK mode

............................................9

C. pH Measurements

........................................................9

a. Measurement with an ATC/Temp probe in the pH-AUTOLOCK

mode

........................................................................9

b. Measurement with manual temperature compensation in the

pH AUTOLOCK mode

..................................................10

c. Measurement with an ATC/Temp probe in the pH NON-

AUTOLOCK mode

......................................................10

d. Measurement with manual temperature compensation in the

pH NON-AUTOLOCK mode.

..........................................11

D. Temperature Measurements

.......................................11

E. mV Measurements

.....................................................11

Measurement in the mV-AUTOLOCK mode

....................11

Measurement in the mV NON-AUTOLOCK mode

.............11

pH BUFFERS..

…………………………….....................12

ERROR DISPLAYS AND TROUBLESHOOTING.......13
SPECIFICATIONS

………………..……........................14

WARRANTY

…………………………….........................15

Содержание VisionPlus pH6175

















Результаты поиска

Содержание VisionPlus pH6175

Отзывы:

Похожие инструкции для VisionPlus pH6175

Бренды по названию

Популярные бренды

JENCO VisionPlus pH6175, Руководство по эксплуатации

Результаты поиска

Содержание VisionPlus pH6175

Отзывы:

Похожие инструкции для VisionPlus pH6175

Бренды по названию

Популярные бренды