JEHNERT SOUND DESIGN AUDI 80 convertible Скачать руководство пользователя

Страница: 7 / 16

7. Installation of the door lining onto car door

7.1. Fit the door lining in contrary order (described on page 3).

7.2.

Cut out the foamed foil like a U (behind the woofers) in order to

improve the acoustic link to the door volume.

use the precisely aligned as pattern for the positioning of fastening points 1- 4

•

marking of fixing points

1- 4:

mark with a thin awl on the door lining and set the holes according to

the marks set before. Use a 6mm drill.

mark speaker cut outs on the door lining. Take away the door-build. Cut out the

speakers’ outlines (see fig.) by means of a compass saw.

Do not cut out the foamed - it will be done after the installation of the door

lining. (s.page 9)

Tip for later retrofit back to original ( see fig.:)

Measure the cut out in size and volume that the speaker have

a good coupling to the door volume and also have enough bearing
surface for a leather covered carton grill, which may recover the cut-outs
(in case you like to retrofit back to original).

4. Handling of door lining / installation of the door panel

3. screw in the screws (1-4 M4x50). Affix the panel with all M4 screws through
the door lining exactly into the original fastening points. Secure with washers
and nuts. Screw only hand tight (screws 1-4), as there is no definitive point of end.
Check again for precise fit, tighten all screws and secure with adhesive or
safety paint.

ll cutting edges of the panel must fit to the door lining snugly

all around without gap.

check all screw connections:

in order to avoid damages to the car door check the length of the staybolts
on the back side of the door lining once again and possibly shorten them.
This does not affect the ventilation.

☞

11 12

Tip for retrofit:
chose your cut-out

that the bearing

surface is kept

☞

76150 - AUDI 80 Convertible/coupé

- 9 -

76150 - AUDI 80 Convertible/coupé

- 6 -



screws 5-13 = Screws premounted

fastening of screws

fix.point 1-4: M 4 x 50
Screws premounted:
fix.point 5-9: M 4 x 40

fix.point 10-13: M 4 x 50



75150

5-9

7. Installation of the door lining onto car door

7.1. Fit the door lining in contrary order (described on page 3).

7.2.

Cut out the foamed foil like a U (behind the woofers) in order to

improve the acoustic link to the door volume.

use the precisely aligned as pattern for the positioning of fastening points 1- 4

•

marking of fixing points

1- 4:

mark with a thin awl on the door lining and set the holes according to

the marks set before. Use a 6mm drill.

mark speaker cut outs on the door lining. Take away the door-build. Cut out the

speakers’ outlines (see fig.) by means of a compass saw.

Do not cut out the foamed - it will be done after the installation of the door

lining. (s.page 9)

Tip for later retrofit back to original ( see fig.:)

Measure the cut out in size and volume that the speaker have

a good coupling to the door volume and also have enough bearing
surface for a leather covered carton grill, which may recover the cut-outs
(in case you like to retrofit back to original).

4. Handling of door lining / installation of the door panel

ll cutting edges of the panel must fit to the door lining snugly

all around without gap.

check all screw connections:

in order to avoid damages to the car door check the length of the staybolts
on the back side of the door lining once again and possibly shorten them.
This does not affect the ventilation.

☞

11 12

Tip for retrofit:
chose your cut-out

that the bearing

surface is kept

☞

76150 - AUDI 80 Convertible/coupé

- 9 -

76150 - AUDI 80 Convertible/coupé

- 6 -



screws 5-13 = Screws premounted

fastening of screws

fix.point 1-4: M 4 x 50
Screws premounted:
fix.point 5-9: M 4 x 40

fix.point 10-13: M 4 x 50



7. Installation of the door lining onto car door

7.1. Fit the door lining in contrary order (described on page 3).

7.2.

Cut out the foamed foil like a U (behind the woofers) in order to

improve the acoustic link to the door volume.

use the precisely aligned as pattern for the positioning of fastening points 1- 4

•

marking of fixing points

1- 4:

mark with a thin awl on the door lining and set the holes according to

the marks set before. Use a 6mm drill.

mark speaker cut outs on the door lining. Take away the door-build. Cut out the

speakers’ outlines (see fig.) by means of a compass saw.

Do not cut out the foamed - it will be done after the installation of the door

lining. (s.page 9)

Tip for later retrofit back to original ( see fig.:)

Measure the cut out in size and volume that the speaker have

a good coupling to the door volume and also have enough bearing
surface for a leather covered carton grill, which may recover the cut-outs
(in case you like to retrofit back to original).

4. Handling of door lining / installation of the door panel

ll cutting edges of the panel must fit to the door lining snugly

all around without gap.

check all screw connections:

in order to avoid damages to the car door check the length of the staybolts
on the back side of the door lining once again and possibly shorten them.
This does not affect the ventilation.

☞

11 12

Tip for retrofit:
chose your cut-out

that the bearing

surface is kept

☞

76150 - AUDI 80 Convertible/coupé

- 9 -

76150 - AUDI 80 Convertible/coupé

- 6 -



screws 5-13 = Screws premounted

fastening of screws

fix.point 1-4: M 4 x 50
Screws premounted:
fix.point 5-9: M 4 x 40

fix.point 10-13: M 4 x 50



7. Installation of the door lining onto car door

7.1. Fit the door lining in contrary order (described on page 3).

7.2.

Cut out the foamed foil like a U (behind the woofers) in order to

improve the acoustic link to the door volume.

use the precisely aligned as pattern for the positioning of fastening points 1- 4

•

marking of fixing points

1- 4:

mark with a thin awl on the door lining and set the holes according to

the marks set before. Use a 6mm drill.

mark speaker cut outs on the door lining. Take away the door-build. Cut out the

speakers’ outlines (see fig.) by means of a compass saw.

Do not cut out the foamed - it will be done after the installation of the door

lining. (s.page 9)

Tip for later retrofit back to original ( see fig.:)

Measure the cut out in size and volume that the speaker have

a good coupling to the door volume and also have enough bearing
surface for a leather covered carton grill, which may recover the cut-outs
(in case you like to retrofit back to original).

4. Handling of door lining / installation of the door panel

ll cutting edges of the panel must fit to the door lining snugly

all around without gap.

check all screw connections:

in order to avoid damages to the car door check the length of the staybolts
on the back side of the door lining once again and possibly shorten them.
This does not affect the ventilation.

☞

11 12

Tip for retrofit:
chose your cut-out

that the bearing

surface is kept

☞

76150 - AUDI 80 Convertible/coupé

- 9 -

76150 - AUDI 80 Convertible/coupé

- 6 -



screws 5-13 = Screws premounted

fastening of screws

fix.point 1-4: M 4 x 50
Screws premounted:
fix.point 5-9: M 4 x 40

fix.point 10-13: M 4 x 50



7. Installation of the door lining onto car door

7.1. Fit the door lining in contrary order (described on page 3).

7.2.

Cut out the foamed foil like a U (behind the woofers) in order to

improve the acoustic link to the door volume.

use the precisely aligned as pattern for the positioning of fastening points 1- 4

•

marking of fixing points

1- 4:

mark with a thin awl on the door lining and set the holes according to

the marks set before. Use a 6mm drill.

mark speaker cut outs on the door lining. Take away the door-build. Cut out the

speakers’ outlines (see fig.) by means of a compass saw.

Do not cut out the foamed - it will be done after the installation of the door

lining. (s.page 9)

Tip for later retrofit back to original ( see fig.:)

Measure the cut out in size and volume that the speaker have

a good coupling to the door volume and also have enough bearing
surface for a leather covered carton grill, which may recover the cut-outs
(in case you like to retrofit back to original).

4. Handling of door lining / installation of the door panel

ll cutting edges of the panel must fit to the door lining snugly

all around without gap.

check all screw connections:

in order to avoid damages to the car door check the length of the staybolts
on the back side of the door lining once again and possibly shorten them.
This does not affect the ventilation.

☞

11 12

Tip for retrofit:
chose your cut-out

that the bearing

surface is kept

☞

76150 - AUDI 80 Convertible/coupé

- 9 -

76150 - AUDI 80 Convertible/coupé

- 6 -



screws 5-13 = Screws premounted

fastening of screws

fix.point 1-4: M 4 x 50
Screws premounted:
fix.point 5-9: M 4 x 40

fix.point 10-13: M 4 x 50



7. Installation of the door lining onto car door

7.1. Fit the door lining in contrary order (described on page 3).

7.2.

Cut out the foamed foil like a U (behind the woofers) in order to

improve the acoustic link to the door volume.

use the precisely aligned as pattern for the positioning of fastening points 1- 4

•

marking of fixing points

1- 4:

mark with a thin awl on the door lining and set the holes according to

the marks set before. Use a 6mm drill.

mark speaker cut outs on the door lining. Take away the door-build. Cut out the

speakers’ outlines (see fig.) by means of a compass saw.

Do not cut out the foamed - it will be done after the installation of the door

lining. (s.page 9)

Tip for later retrofit back to original ( see fig.:)

Measure the cut out in size and volume that the speaker have

a good coupling to the door volume and also have enough bearing
surface for a leather covered carton grill, which may recover the cut-outs
(in case you like to retrofit back to original).

4. Handling of door lining / installation of the door panel

ll cutting edges of the panel must fit to the door lining snugly

all around without gap.

check all screw connections:

in order to avoid damages to the car door check the length of the staybolts
on the back side of the door lining once again and possibly shorten them.
This does not affect the ventilation.

☞

11 12

Tip for retrofit:
chose your cut-out

that the bearing

surface is kept

☞

76150 - AUDI 80 Convertible/coupé

- 9 -

76150 - AUDI 80 Convertible/coupé

- 6 -



screws 5-13 = Screws premounted

fastening of screws

fix.point 1-4: M 4 x 50
Screws premounted:
fix.point 5-9: M 4 x 40

fix.point 10-13: M 4 x 50



7. Installation of the door lining onto car door

7.1. Fit the door lining in contrary order (described on page 3).

7.2.

Cut out the foamed foil like a U (behind the woofers) in order to

improve the acoustic link to the door volume.

use the precisely aligned as pattern for the positioning of fastening points 1- 4

•

marking of fixing points

1- 4:

mark with a thin awl on the door lining and set the holes according to

the marks set before. Use a 6mm drill.

mark speaker cut outs on the door lining. Take away the door-build. Cut out the

speakers’ outlines (see fig.) by means of a compass saw.

Do not cut out the foamed - it will be done after the installation of the door

lining. (s.page 9)

Tip for later retrofit back to original ( see fig.:)

Measure the cut out in size and volume that the speaker have

a good coupling to the door volume and also have enough bearing
surface for a leather covered carton grill, which may recover the cut-outs
(in case you like to retrofit back to original).

4. Handling of door lining / installation of the door panel

ll cutting edges of the panel must fit to the door lining snugly

all around without gap.

check all screw connections:

in order to avoid damages to the car door check the length of the staybolts
on the back side of the door lining once again and possibly shorten them.
This does not affect the ventilation.

☞

11 12

Tip for retrofit:
chose your cut-out

that the bearing

surface is kept

☞

76150 - AUDI 80 Convertible/coupé

- 9 -

76150 - AUDI 80 Convertible/coupé

- 6 -



screws 5-13 = Screws premounted

fastening of screws

fix.point 1-4: M 4 x 50
Screws premounted:
fix.point 5-9: M 4 x 40

fix.point 10-13: M 4 x 50



7. Installation of the door lining onto car door

7.1. Fit the door lining in contrary order (described on page 3).

7.2.

Cut out the foamed foil like a U (behind the woofers) in order to

improve the acoustic link to the door volume.

use the precisely aligned as pattern for the positioning of fastening points 1- 4

•

marking of fixing points

1- 4:

mark with a thin awl on the door lining and set the holes according to

the marks set before. Use a 6mm drill.

mark speaker cut outs on the door lining. Take away the door-build. Cut out the

speakers’ outlines (see fig.) by means of a compass saw.

Do not cut out the foamed - it will be done after the installation of the door

lining. (s.page 9)

Tip for later retrofit back to original ( see fig.:)

Measure the cut out in size and volume that the speaker have

a good coupling to the door volume and also have enough bearing
surface for a leather covered carton grill, which may recover the cut-outs
(in case you like to retrofit back to original).

4. Handling of door lining / installation of the door panel

ll cutting edges of the panel must fit to the door lining snugly

all around without gap.

check all screw connections:

in order to avoid damages to the car door check the length of the staybolts
on the back side of the door lining once again and possibly shorten them.
This does not affect the ventilation.

☞

11 12

Tip for retrofit:
chose your cut-out

that the bearing

surface is kept

☞

76150 - AUDI 80 Convertible/coupé

- 9 -

76150 - AUDI 80 Convertible/coupé

- 6 -



screws 5-13 = Screws premounted

fastening of screws

fix.point 1-4: M 4 x 50
Screws premounted:
fix.point 5-9: M 4 x 40

fix.point 10-13: M 4 x 50



7. Installation of the door lining onto car door

7.1. Fit the door lining in contrary order (described on page 3).

7.2.

Cut out the foamed foil like a U (behind the woofers) in order to

improve the acoustic link to the door volume.

use the precisely aligned as pattern for the positioning of fastening points 1- 4

•

marking of fixing points

1- 4:

mark with a thin awl on the door lining and set the holes according to

the marks set before. Use a 6mm drill.

mark speaker cut outs on the door lining. Take away the door-build. Cut out the

speakers’ outlines (see fig.) by means of a compass saw.

Do not cut out the foamed - it will be done after the installation of the door

lining. (s.page 9)

Tip for later retrofit back to original ( see fig.:)

Measure the cut out in size and volume that the speaker have

a good coupling to the door volume and also have enough bearing
surface for a leather covered carton grill, which may recover the cut-outs
(in case you like to retrofit back to original).

4. Handling of door lining / installation of the door panel

ll cutting edges of the panel must fit to the door lining snugly

all around without gap.

check all screw connections:

in order to avoid damages to the car door check the length of the staybolts
on the back side of the door lining once again and possibly shorten them.
This does not affect the ventilation.

☞

11 12

Tip for retrofit:
chose your cut-out

that the bearing

surface is kept

☞

76150 - AUDI 80 Convertible/coupé

- 9 -

76150 - AUDI 80 Convertible/coupé

- 6 -



screws 5-13 = Screws premounted

fastening of screws

fix.point 1-4: M 4 x 50
Screws premounted:
fix.point 5-9: M 4 x 40

fix.point 10-13: M 4 x 50



7. Installation of the door lining onto car door

7.1. Fit the door lining in contrary order (described on page 3).

7.2.

Cut out the foamed foil like a U (behind the woofers) in order to

improve the acoustic link to the door volume.

use the precisely aligned as pattern for the positioning of fastening points 1- 4

•

marking of fixing points

1- 4:

mark with a thin awl on the door lining and set the holes according to

the marks set before. Use a 6mm drill.

mark speaker cut outs on the door lining. Take away the door-build. Cut out the

speakers’ outlines (see fig.) by means of a compass saw.

Do not cut out the foamed - it will be done after the installation of the door

lining. (s.page 9)

Tip for later retrofit back to original ( see fig.:)

Measure the cut out in size and volume that the speaker have

a good coupling to the door volume and also have enough bearing
surface for a leather covered carton grill, which may recover the cut-outs
(in case you like to retrofit back to original).

4. Handling of door lining / installation of the door panel

ll cutting edges of the panel must fit to the door lining snugly

all around without gap.

check all screw connections:

in order to avoid damages to the car door check the length of the staybolts
on the back side of the door lining once again and possibly shorten them.
This does not affect the ventilation.

☞

11 12

Tip for retrofit:
chose your cut-out

that the bearing

surface is kept

☞

76150 - AUDI 80 Convertible/coupé

- 9 -

76150 - AUDI 80 Convertible/coupé

- 6 -



screws 5-13 = Screws premounted