background image

Packing unit

  Check list

door panel, covered 

(right / left)

Speaker grill, covered 

(right / left)

Tweeter 26 mm
Tweeter mounting bowl

(

with 6Ktn.Screw M4x8 u. Washer ø12mm)

Midrange 100 mm Q 

assembly ring

woofer 160 mm 

(each mounted on the panel with 2 Sheet metal-screws)

Crossover 

(right / left)

standart cables for subwoofer 

(right / left)

Hardware bag:

Flat head screws, M 4 x 50

Hex nut M 4

Washer Ø 12mm 

(f.flat head screws, lower edge of panel)

Washer Ø 20mm 

(f.head screws M4x50 

on the top

 )

Washer Ø 20mm 

as spacer for Velcro fastener

Sheet metal screws,black 3,9x13 

(f. woofer)

Velcro strip à 2,5 cm 

(reserve)

Preassembled hardware:

Velcro fastener plus strips

Sheet metal screws, black 3,9x13

(f. subwoofer)

Flat head screws, M 4 x 40

Flat head screws, M 4 x 50

The product was carefully packed and checked for its completeness. If you find anything missing, damaged or
defective, please notice our guarantee services on the back of these assembly instructions.

Packing list

       76150 - AUDI 80 Convertible/coupé

- 13 -

              © JEHNERT SOUND DESIGN

76150 - AUDI 80 Convertible/coupé              - 2 -               © JEHNERT SOUND DESIGN

2

2
2
2
2
8
2
2

8

26
18

8
2

16

4

10

16

10

8

T e c h n i c a l   i n f o r m a t i o n

Equipment:                 without co-passenger airbag,
                                 electric and/ or mechanical window control

Model/ year   :           AUDI 80, type 89

Insulation:

       Insulation not necessary

Note about setting:      To obtain optimal stereoscopic sound, all settings 
                                  on the radio (bass, treble, loudness etc) should be
                                  set to zero or neutral.

Recommended
amplifier power  :

from 2x 200 - 360 Watt RMS / 4 Ohm

Metal cutwork :                 not necessary

Cut-outs for loudspeaker/  4 x 144mm (max.outer dimensions subwoofer 165 mm)
each side

                                   (max.installation depth subwoofer   65 mm)

only compatible with JEHNERT Sound System

Sound-System:                 3-ways
                                        4 x 160 mm subwoofer/ side

               1 x 100 mm midrange / side
               1 x   26 mm tweeter / side
                car-customized crossover network

                                        max.continuous Watt/RMS:

2 x 300/500Watt

                                        car specific frequency range:              47-22.000 Hz
                                        Total impedance:                 

4 Ohm

Time for Installation          car hifi-specialist: 4 hours

We reserve the right to make technical changes, as well as development.

20

12

75150

Содержание AUDI 80 convertible

















Отзывы: