![Jeep WRANGLER 2017 Скачать руководство пользователя страница 188](http://html2.mh-extra.com/html/jeep/wrangler-2017/wrangler-2017_owners-manual_4166205188.webp)
•
Check Gascap (refer to “Refueling The Vehicle” in
“Starting And Operating” for further information)
•
Oil Change Required (with a single chime)
•
ECO (Fuel Saver Indicator) — if equipped
Gear Shift Indicator (GSI) — If Equipped
— Up Shift Indicator Light
— Down Shift Indicator Light
The Gear Shift Indicator (GSI) system is enabled
on vehicles with a manual transmission, or when
a vehicle with an automatic transmission is in
manual shift mode. The GSI provides the driver
with a visual indication when the recommended gear shift
point has been reached. This indication notifies the driver
that changing gear will allow a reduction in fuel consump-
tion. When the up shift indicator is shown on the display,
the GSI is advising the driver to engage a higher gear.
When the down shift indicator is shown on the display, the
GSI is advising the driver to engage a lower gear.
The GSI indicator remains illuminated until the driver
changes gear, or the driving conditions return to a situation
where changing gear is not required to improve fuel
consumption.
Oil Change Required
Your vehicle is equipped with an engine oil change indi-
cator system. The “Oil Change Required” message will
display in the instrument cluster display for approximately
10 seconds after a single chime has sounded to indicate the
next scheduled oil change interval. The engine oil change
indicator system is duty cycle based, which means the
engine oil change interval may fluctuate dependent upon
your personal driving style.
Unless reset, this message will continue to display each
time you turn the ignition switch to the ON position. To
turn off the message temporarily, push and release the
MENU
button. To reset the oil change indicator system
(after performing the scheduled maintenance), perform the
following procedure:
1. Turn the ignition switch to the ON position.
Do not start
the engine
.
2. Fully push the accelerator pedal slowly three times
within 10 seconds.
186
GETTING TO KNOW YOUR INSTRUMENT PANEL
Содержание WRANGLER 2017
