manualshive.com logo in svg

Jeep Liberty 2011, Руководство пользователя, Страница: 349 / 540

Поделиться
Скачать
Jeep Liberty 2011 Скачать руководство пользователя страница 349

Disabling and Enabling HSA

This feature can be turned on or turned off. To change the
current setting, proceed as follows:

For vehicles equipped with the Electronic Vehicle Infor-
mation Center (EVIC), refer to “Hill Start Assist,” under

⬙

Personal Settings (Customer Programmable Features),”

under “Electronic Vehicle Information Center (EVIC)” in
“Understanding Your Instrument Panel” for further in-
formation.

For vehicles not equipped with the EVIC, perform the
following steps:

NOTE:

You must complete Steps 1 through 8 within

90 seconds.

1. Center the steering wheel (front wheels pointing
straight forward).

2. Shift the transmission into PARK.

3. Apply the parking brake.

4. Start the engine.

5. Rotate the steering wheel one-half turn to the left.

6. Press the “ESC Off” button located in the lower switch
bank below the climate control four times within twenty
seconds. The “ESC Off Indicator Light” should turn on
and turn off two times.

7. Rotate the steering wheel back to center and then an
additional one-half turn to the right.

8. Turn the ignition switch to the OFF position and then
back to the ON position. If the sequence was completed
properly, the “ESC Off Indicator Light” will blink several
times to confirm HSA is disabled.

9. Repeat these steps if you want to return this feature to
its previous setting.

5

STARTING AND OPERATING

347

Содержание Liberty 2011





























































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов