Jeep Liberty 2011 страница 319 Скачать руководство пользователя | Manualshive

Страница: 319 / 540

background image

2 (Second)

This range is used for moderate grades and to assist
braking on dry pavement or in mud and snow. Begins at
a stop in low gear with automatic upshift into second
gear. Will not shift into third gear.

1 (First)

This range is used for hard pulling at low speeds in mud,
sand, snow, or on steep grades. Begins and stays in low
gear with no upshift. Provides engine compression brak-
ing at low speeds.

Overdrive Operation

The overdrive automatic transmission contains an elec-
tronically controlled fourth gear (OVERDRIVE). The
transmission will automatically shift from third gear into
OVERDRIVE if the following conditions are present:

•

the shift lever is in DRIVE

•

vehicle speed is above approximately 30 mph
(48 km/h)

•

the TOW/HAUL button has not been activated

The transmission will downshift from OVERDRIVE to
DRIVE if the accelerator pedal is fully pressed at vehicle
speeds above approximately 35 mph (56 km/h).

When To Use TOW/HAUL Mode

When driving in hilly areas, towing a trailer, carrying a
heavy load, etc., and frequent transmission shifting oc-
curs, press the TOW/HAUL button. This will improve
performance and reduce the potential for transmission
overheating or failure due to excessive shifting. When
operating in TOW/HAUL mode, the transmission will
shift into third gear.

5

STARTING AND OPERATING

317

«
...
317
318
319
320
321
...
»

Содержание Liberty 2011





























































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Liberty 2011

Бренд: AAMP of America Страницы: 6

Бренд: cam Страницы: 28

Бренд: Harbor Freight Tools Страницы: 4

UNIVERSAL CJ-2A

Бренд: Jeep Страницы: 27

Бренд: Jeep Страницы: 228

Бренд: Jeep Страницы: 108

Бренд: Jeep Страницы: 525

Бренд: OEM Tools Страницы: 4

Бренд: Yakima Страницы: 8

Бренд: Mobile Create Страницы: 15

2007 MazdaSpeed6

Бренд: Mazda Страницы: 12

Бренд: AC Schnitzer Страницы: 20

Бренд: Nuna Страницы: 17

Бренд: Toyota Страницы: 295

Бренд: Whispbar Страницы: 15

Бренд: ECS Electronics Страницы: 42

Бренд: Jaeger Страницы: 13

Бренд: Lexus Страницы: 609

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды