Jeep Grand Cherokee SRT 2017 Скачать руководство пользователя | Manualshive

Страница: 357 / 589

background image

Improper weight distributions can have an adverse effect
on the way your vehicle steers and handles and the way
the brakes operate.

CAUTION!

Do not load your vehicle any heavier than the GVWR
or the maximum front and rear GAWR. If you do, parts
on your vehicle can break, or it can change the way
your vehicle handles. This could cause you to lose
control. Also overloading can shorten the life of your
vehicle.

TRAILER TOWING

In this section you will find safety tips and information on
limits to the type of towing you can reasonably do with
your vehicle. Before towing a trailer, carefully review this
information to tow your load as efficiently and safely as
possible.

To maintain the New Vehicle Limited Warranty coverage,
follow the requirements and recommendations in this
manual concerning vehicles used for trailer towing.

Common Towing Definitions

The following trailer towing related definitions will assist
you in understanding the following information:

Gross Vehicle Weight Rating (GVWR)

The GVWR is the total allowable weight of your vehicle.
This includes driver, passengers, cargo and tongue weight.
The total load must be limited so that you do not exceed
the GVWR. Refer to “Vehicle Loading/Vehicle Certification
Label” in “Starting And Operating” for further informa-
tion.

Gross Trailer Weight (GTW)

The GTW is the weight of the trailer plus the weight of all
cargo, consumables and equipment (permanent or tempo-
rary) loaded in or on the trailer in its

⬙

loaded and ready for

operation

⬙

condition.

The recommended way to measure GTW is to put your
fully loaded trailer on a vehicle scale. The entire weight of
the trailer must be supported by the scale.

Gross Axle Weight Rating (GAWR)

The GAWR is the maximum capacity of the front and rear
axles. Distribute the load over the front and rear axles
evenly. Make sure that you do not exceed either front or

6

STARTING AND OPERATING

355

«
...
355
356
357
358
359
...
»

Содержание Grand Cherokee SRT 2017














































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Grand Cherokee SRT 2017

Бренд: LaserTrack Страницы: 12

CK 3000 Evolution

Бренд: Parrot Страницы: 2

Бренд: REVCAMUK Страницы: 4

Бренд: TBC Страницы: 12

Бренд: Prorack Страницы: 14

Бренд: Oypla Leisure Страницы: 4

Бренд: Camoplast Страницы: 19

Бренд: Acura Страницы: 6

Бренд: GROM Audio Страницы: 20

Бренд: Ford Страницы: 4378

Бренд: Toyota Страницы: 549

PLATINUM HT051202

Бренд: Haltech Страницы: 10

Бренд: Ford Страницы: 2

Бренд: Toyota Страницы: 596

Бренд: Haltech Страницы: 12

Бренд: Laser Страницы: 23

Бренд: ikross Страницы: 2

Бренд: MSD Ignition Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды