manualshive.com logo in svg
background image

            

          INSTALLATION INSTRUCTIONS  

          FOR 

         50-0284x-015 SERIES    1181313 

      JEEP GRAND CHEROKEE  

      OVERHEAD CONSOLE for use with FLIPDOWN VIDEO SYSTEM 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 
              

             

             These instructions are intended for use only by experienced professionals in the automotive 

                 customizing business. Special tools and equipment, as well as specialized handling and care 
                 of product during installation, may be required. Before beginning this installation, carefully read 

through the following instructions. 

Use extreme care when cutting headliner material. 

Check for wiring or other componentry above headliner material. Cut only where indicated. 
 
Materials/ Tools required for this installation: 

 

1.   #2 Phillips screwdriver 

2.   Powered screwdriver or drill with adapter 

3.   Awl or similar tool 

4.   Razor knife or similar 

5.   18 GA wire 4' - 6' 

6.   Scissors 

7.    5/16” Hex Socket Bit 

8.   Safety Goggles 

9.   Test light 

10.  3/8”  Drill Bit 

11. Audiovox Series 640/650 Video Module 

 

                         

    NOT FOR VEHICLES EQUIPPED WITH SUN ROOF.  

 
 

         

                                     

 

June 2, 1999 

Printed in the U.S.A 

INSTALLATION  INSTRUCTION  # 44-0031A 

Содержание 50-0284x-015 Series







Отзывы: