![JCM ivizion ld Скачать руководство пользователя страница 65](http://html1.mh-extra.com/html/jcm/ivizion-ld/ivizion-ld_operation-and-maintenance_3544215065.webp)
P/N 960-100929R_Rev. 7 {EDP #148849}
© 2017, JAPAN CASH MACHINE CO., LTD.
4 - 9
Disassembly/Reassembly
iVIZION® Series Next-Generation Banknote Acceptor Unit
Section 4
Stacker Motor & Transport Motor
Removals
To remove the Stacker Motor and the Transport
Motor proceed as follows:
1. Remove the TR-ST Motor Gear (Figure 4-32
a
)
and the two (2) mounting Screws (Figure 4-32
b
1
&
b
2
) securing the Motor Module in place.
2. Remove the Stacker Motor (Figure 4-32
c
) from
the Motor Module Assembly.
Bezel Hold Clips A & B Removal
To remove Bezel Hold Clips “A” and Bezel Hold
Clips “B” proceed as follows:
1. Remove the two (2) laminated, M2.6x6 Phillips
Self-Tapping Screws (Figure 4-33
a
1
&
a
2
) from
the Bezel, and then remove Bezel Hold Clip “A”
from the left side of the Assembly (Figure 4-33
b
).
2. Remove the two (2) laminated M2.6x6 Phillips
Self-Tapping Screws (Figure 4-33
a
3
&
a
4
) from
the Bezel, and then remove Bezel Hold Clip “B”
from the right side of the Assembly (Figure 4-33
c
).
Sensor Transfer Board/CIS FFC/
Transmissive Light FFC & Upper
UV FPC Sensor Removals
To remove the Sensor Transfer Board, the CIS FFC
Sensor, the Transmissive Light FFC Sensor and the
Upper UV FPC Sensor proceed as follows:
1. Open the Validation Section and release the six
(6) Upper Cover Click-tab Stops (Figure 4-34
a
1
to
a
6
) by using a small Screwdriver.
2. Remove the Upper Cover (Figure 4-34
b
) from
the Upper Guide.
3. Remove the two (2) mounting Screws (Figure 4-
a
1
&
a
2
) securing the Sensor Transfer Board
Assembly to the Transport.
4. Remove the CIS FFC (Figure 4-35
b
), the Trans-
missive Light FFC (Figure 4-35
c
), and the Upper
UV FPC (Figure 4-35
d
) from the Validation
Head.
5. Unplug the two (2) Flat Flexible Cables (FFC)
e
1
&
e
2
) and then remove the Sensor
Transfer Board Assembly (Figure 4-35
f
) off of
the Validation Head; then
6. Remove the CIS FFC, the Transmissive Light
FFC and the Upper FPC from the Validation Unit.
NOTE: Follow the same procedure to
remove the Transport Motor on the
opposite side.
Figure 4-32
Figure 4-32
Stacker & Transport Motor Removal
a
b
2
b
1
c
NOTE: When reassembling the TR-
ST Motor Gear, a Motor Gear
Assembly Pressure Bar will be
required.
Figure 4-33
Figure 4-33
Bezel Hold Chips A&B Removal
a
2
a
1
a
3
a
4
b
c
NOTE: Use a T6 “TORX” Torque
Wrench Driver when reattaching
Bezel Hold Clips “A” and “B” onto the
Transport Unit.
Figure 4-34
Figure 4-34
Upper Cover Removal
1
a
2
a
3
a
6
a
4
a
5
Figure 4-35
Sensor Transfer Board Assembly,
CIS FFC, Transmissive Light & Upper UV FPC
Cable Removal
Figure 4-35
Sensor Transfer Board Assembly,
CIS FFC, Transmissive Light &
Upper UV FPC Cable Removal
b
c
d
e
1
e
2
f