JBSYSTEMS Light LED CROSSFIRE, Руководство пользователя

Страница: 4 / 29

ENGLISH OPERATION MANUAL
JB SYSTEMS ® 3/53 LED CROSSFIRE
OVERHEAD RIGGING

Important: The installation must be carried out by qualified service personal only. Improper
installation can result in serious injuries and/or damage to property. Overhead rigging requires
extensive experience! Working load limits should be respected, certified installation materials
should be used, the installed device should be inspected regularly for safety.

Make sure the area below the installation place is free from unwanted persons during rigging, de-rigging
and servicing.

Locate the fixture in a well ventilated spot, far away from any flammable materials and/or liquids. The
fixture must be fixed
at least 50cm from surrounding walls.

The device should be installed out of reach of people and outside areas where persons may walk by or be
seated.

Before rigging make sure that the installation area can hold a minimum point load of 10times the device’s
weight.

Always use a certified safety cable that can hold 12times the weight of the device when installing the unit.
This secondary safety attachment should be installed in a way that no part of the installation can drop
more than 20cm if the main attachment fails.

The device should be well fixed; a free-swinging mounting is dangerous and may not be considered!

Don’t cover any ventilation openings as this may result in overheating.

The operator has to make sure that the safety-relating and machine-technical installations are approved by
an expert before using them for the first time. The installations should be inspected every year by a skilled
person to be sure that safety is still optimal.
DESCRIPTION:
1. Mains input with IEC socket and integrated fuse holder, connect the supplied mains cable here.
2. Mains output with IEC socket: you can use a special IEC power cable to connect this output with the
mains input of the next unit for easier linking.
3. Hanging bracket with 2 knobs on both sides to fasten the unit and a mounting hole to fix a mounting
hook.
4. Safety eye, used to attach a safety cable when the unit is rigged, see paragraph “overhead rigging”
5. Optical lenses
6. DMX input: 3pin male XLR-connector used to connect universal DMX-cables. This input receives
instructions from a DMX-controller.
7. DMX output: 3pin female XLR-connector used to connect the effect with the next unit in the DMX chain.
8. Internal microphone
ENGLISH OPERATION MANUAL
JB SYSTEMS ® 4/53 LED CROSSFIRE
9. ¼” jack used to connect an optional CA-8 controller.
10. Din-5pin input, used to connect an optional wireless receiver, named RF-8R.
11. Slave LED: is lit when the unit is in slave mode
12. Sound LED: blinks to the rhythm of the music while the unit is in audio mode
13. DMX LED: is lit when the unit receives a DMX-signal
14. Master LED: is lit when the unit is switched as master
15. MENU button: used to select the different menu items
16. DOWN button: to go back in the menu and to lower the values shown on the display.
17. UP button: to go up in the menu and to increase the values shown on the display.
18. ENTER button: used to confirm your choice.
19. DISPLAY shows the various menus and the selected functions.
HOW TO SETUP:
MAIN MENU:

To select any of the menu options, press the
MENU button up to when the required one is
shown on the display.

Select the function with the ENTER button.
The display will blink.

Use DOWN and UP button to choose the
desired menu option.

Once the required menu option is selected,
press the
ENTER button to select.
To go back to the functions without any change
press the
MENU button during 2 seconds or
just wait 10 seconds.
DMX512 Address Setting
Used to set the starting address in a DMX
setup.

Press the MENU button until is shown
on the display.

Press the ENTER button, the display starts
blinking.

Use DOWN and UP buttons to change the
DMX512 address.

Once the correct address shows on the
display, press the ENTER button to save it.

Press the MENU button for about 2 seconds
to return to running mode.
Channel Mode

Press the MENU button until is shown
on the display.

Press the ENTER button, the display starts
blinking.

Use DOWN and UP button to select the
1Ch
(1Channel),
1MSL
(1 Channel master/slave)
or
4Ch
(4 Channel) mode.

Once the right mode is selected, press the
ENTER button to confirm.

Press the MENU button for about 2 seconds to return to running mode.