background image

www.jbstools.com

6

IMPortant saFEtY 

warnInGs

DO NOT 

operate the pallet truck unless you are familiar with this product and have been trained 

or authorised to do so.

DO NOT

 operate the pallet truck on sloping grounds.

DO NOT

 

handle unstable or loosely stacked loads.

NEVER 

place any part of your body in the lifting mechanism or under the forks or load.

DO NOT

 use the pallet truck to lift and carry people or loads over people.

NEVER

 overload the pallet truck.

DO NOT

 operate a pallet truck that has been deemed unsafe after inspection/ service.

DO NOT

 operate a pallet truck if you are not physically capable of safely handling the pallet truck 

with a load.

ALWAyS

 visually inspect the pallet truck for damage or faults before use especially the wheels, 

handle assembly, forks and lowering control.

DO

 wear gloves and safety boots when operating the pallet truck.

LOWER

 the forks to the lowest height when the pallet truck is not in use.

ALWAyS

 place loads centrally across the forks and not at the end of the forks

PLEASE NOTE

 that the capacity of the pallet truck assumes an evenly distributed load with the 

centre of the load being at the halfway point of the length of the forks

CONFIRM

 that the length of the forks matches the length of the pallet.

OPERATE

 the pallet truck on level, flat solid surfaces which are capable of supporting the fully 

loaded pallet truck

Содержание JBS-PT-AC25













Отзывы: