background image

4

IMPORTANT SAFETY INSTRUCTIONS 

1. Read these instructions. 

2.  Keep these instructions. 

3.  Heed all warnings. 

4.  Follow all instructions. 

5.  Do not use this apparatus near water. 

6.  Clean only with dry cloth.  

7.  Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. 

8.  Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus 

(including amplifiers) that produce heat. 

9.  Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two 

blades with one wider than the other. A grounding-type plug has two blades and a third grounding 
prong. The wide blade or the third prong are provided for your safety. If the provided plug does not 
fit into your outlet, consult an electrician for replacement of the obsolete outlet.  

10. Protect the power cord from being walked on or pinched, particularly at plugs, convenience 

receptacles, and the point where they exit from the apparatus.  

11. Only use attachments/accessories specified by the manufacturer.  

12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, 

or sold with the apparatus. When a cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over.  

13. Unplug this apparatus during lightning storms or when unused for long periods of time.  

14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has 

been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled 
or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does 
not operate normally, or has been dropped. 

15. 

WARNING:

To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. 

16. Do not expose this equipment to dripping or splashing and ensure that no objects filled with liquids, 

such as vases, are placed on the equipment.

17. To completely disconnect this apparatus from the AC Mains, disconnect the power supply cord plug

from the AC receptacle. 

18. The mains plug of the power supply cord shall remain readily operable. 

SECTION 1. SAFETY INSTRUCTIONS

VRX_Powered_UsersGuid012808 copy 3.qxp  1/30/08  4:52 PM  Page 4

Содержание VRX932LAP





























Отзывы: