7
English
Push small tab
toward battery slot.
Pull battery
drawer out.
Insert new battery
with “+” side up, and
slide battery drawer
back into remote.
Declaration of Conformity
We, Harman Consumer Group, Inc.
2, route de Tours
72500 Château du Loir
France
declare in own responsibility that the product
described in this owner’s manual is in compliance
with technical standards:
EN 55013:2001+A1:2003
EN 55020:2002+A1:2003
EN 61000-3-2:2000
EN 61000-3-3:1995+A1:2001
EN 60065:2002
Laurent Rault
Harman Consumer Group, Inc.
Château du Loir, France 6/08
Vertically Stand-Mounting the
Receiver Module
Step 1
.
Remove the corner screws located on the left side of the receiver
module when viewed from the bottom, looking at the front, as shown
in Figure 8.
Figure 8.
Step 2.
Rest the receiver module on top of the stand and reattach the two
screws that were removed in Step 1 through the holes in the stand
into the bottom of the receiver module, as shown in Figure 9.
Figure 9.
Step 3.
Rotate the JBL logo 90˚ by gently pulling it out and turning it.
Vertically Mounting the
Transmitter Module
Step 1.
Attach the four included self-adhesive rubber feet in the recesses
on the side of the transmitter module.
Step 2.
Rotate the JBL logo to a vertical orientation.
Remote Control Battery Replacement
CAUTION:
When replacing the lithium battery in the remote, make sure that the
replacement battery is inserted in correct polarity. Place the battery so that
its positive (+) side faces up with the tray held so that the surface with the
dot and (+) is facing up.
Remote-control-battery installation
CAUTION:
DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY
REPLACED.
REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE (CR2032).
WARNING:
DO NOT EXPOSE BATTERIES TO EXCESSIVE HEAT SUCH AS
DIRECT SUNLIGHT, FIRE OR THE LIKE.
Dispose of dead batteries in accordance with local regulations.
MAINTENANCE AND SERVICE
The speaker and transmitter enclosures may be cleaned using a soft
cloth to remove fingerprints or to wipe off dust.
All wiring connections should be inspected and cleaned or remade
periodically. The frequency of maintenance depends on the metals
involved in the connections, atmospheric conditions and other
factors, but once per year is the minimum.
In the event that your system ever needs service, contact your local
JBL dealer or distributor, or visit www.jbl.com for a service center
near you.
SPECIFICATIONS
Frequency Range:
20Hz – 20kHz
(+0dB, –1dB)
Amplifier Output:
50 Watts per channel
Signal-to-Noise Ratio:
80dBA
Operating Range:
Up to 22m (70'), depending upon conditions
RF Operating Frequency:
2.4GHz
Power Requirement:
100V – 240V AC, 50/60Hz
Power consumption
50W
Operating temperature
+5˚C to +40˚C(+41˚F to 104.5˚F)
Operating humidity
5% to 85% (No condensation)
Dimensions
Transmitter Module:
29mm x 158mm x 116mm(1-1/8" x 6-3/16" x 4-5/8")
(H x W x D)
95mm (3-3/4") high with antenna extended
Receiver Module:
29mm x 154mm x 98mm (1-1/8" x 6" x 3-7/8" )
(H x W x D)
95mm (3-3/4") high with antenna extended
Weight
Transmitter Module:
0.3kg (0.6 lb)
Receiver Module:
0.4kg (0.9 lb)
Features, specifications and appearance are subject to change
without notice.
0053CSK - JBL OnAir WEM-1 ENG v6:34199_Control_2_4G_Eng 22/08/08 14:27 Side 7
Содержание On-Air WEM-1
Страница 1: ...JBL ON AIR WEM 1 OWNER S GUIDE English...
