JBL MR-140 Скачать руководство пользователя страница 5

10

Important notes

3

Prior to the final installation, carry out a sound check. If high distortion or intermittent 
sound is experienced, it is possible that the wiring from the CD receiver to the boat's 
electrical system is poor or that the battery needs recharging.
If the battery and its charging circuit are OK, then rewire the red fused wire of the CD 
player directly to the positive terminal (+) of the boat battery. 
Marine accessory shops stock the connector blocks and the 10 Amp cable which may 
be necessary for extending the fuse wire connection.

   

Grounding 

Make sure that the black wire on the wiring harness is connected to a good ground 
point on the boat. If the chassis of the boat is used as a grounding point, make sure 
that the surface is scraped clean from the metal before attaching the wire to it. 
It is preferable to connect the black ground wire directly to negative terminal (-) of the 
boat battery.    

   Warning: polarity... 

 

This model is only suitable for use in boats which have a negative ground system, 
e. g.. : the negative terminal of the boat

 

battery is connected to the chassis.

   Connecting the speakers and power cables

Before you wire your system, disconnect your boats battery's positive (+) cable. 
This helps prevent damage in case of a short. When you complete the wiring, 
reconnect the battery cable and test your marine stereo. When connecting your 
marine stereo's black ground wire, be sure to connect the wire to a metal part of your 
boat or preferably to the negative (-) terminal of the boat battery. 

POSITIVE
CHASSIS

NEGATIVE
CHASSIS

Operating the Radio

1.

 Press the 

BND button (6)

 to select the desired band FM1, FM2, FM3, AM1 or AM2.    

2. Manual / Seek tuning buttons (7) :  

Press this button quickly to activate the 

Seek mode. The Seek mode will automatically seek up or down the wave band and 
stop at the next station of sufficient signal strength. Press this button (7) for longer 
than 2 seconds to advance the tuning up or down the wave band.

3. Manual station store:  

Select the desired band and tune to a radio station to be 

memorized. Choose the preset button memory location 1-6 into which the station is
to be stored and press and hold that preset button for 2 seconds. The station will 
now be entered into the preset memory. 6 stations can be memorized on each of the 
FM1, FM2, FM3, AM1 & AM2.

4. A.PS - Auto store function. (16)

Depress and hold button (16) for approximately 2 seconds until you hear a signal
which confirms the memory function is complete and the display shows "SEARCH". 
Automatically six strong stations are stored on the station buttons 1 - 6. 
You can override the preset station on any button by manually setting a new frequency.
Press the A.PS button quickly to hear 10 seconds of all stored presets. Quickly press it 
again to cancel.

5. Presets

Press the preset buttons 1-6  to find the memorized radio stations.

6. Stereo - / mono - reception

The unit is prepared for stereo reception as soon as it is turned on. If you now receive 
an FM-station which airs a stereo broadcast in the course of its program, 
the corresponding indication appears on the display.
 

1

2

7

4

6

8

10

11

12

13

14

5

3

15

PWR

MUT

TUN

A.PS

BND

MOD

IEQ

T/F

HI-POWER 4x45 Watts

COMPACT DISC PLAYER

1

us

p

h

 

 

L

S

O

E

V

L

  

 RPT

RDM

INT

5

6

9

16

Содержание MR-140









Отзывы: