manualshive.com logo in svg

JBL MR-140, Руководство по эксплуатации, Страница: 2 / 8

Поделиться
Скачать
JBL MR-140 Скачать руководство пользователя страница 2

13

Trouble shooting guide

INTERFERENCE ON RADIO

    Poor atmospheric conditions - Try again later in the day.    

    Antenna / lead broken or damaged.

Power Output : 

 4 x 45 watts

Power Supply :

 DC + 12V

                        Negative Ground

Speaker Impedance:

  4 ohm

Tuning Range :

 530~1710KHz  (USA)

                        522~1620KHz (EUR)           

Sensitivity :

 35dB / uV

Tuning Range :

 87.5~107.9MHz(USA)

                        87.5~108MHz (EUR)

Sensitivity :

 

10dB / uV

Separation :

 30dB

FM TUNER

COMPACT DISC

AUDIO AMP & GENERAL

Freq. Response :

 20 Hz-20 KHz

Total Harmonic Distortion :

 0.8%

Signal - Noise Ratio :

 65 dB

Dynamic Range :

 90 dB

DISTORTED AUDIO

Specifications

AM TUNER 

Check loudspeaker wiring.

This product contains a biamp. It is important not to connect the front 

loudspeaker ground to the rear speaker ground.

Faulty loudspeaker.

Distortion at highest volume levels may be normal, as amplifier has 

reached maximum power output. Otherwise the power and ground wire s 

gauge might be too small (use 10amp cable or more).

Reduce the bass effect or switch off the loudness mode.

Boat battery and or charging circuit may be faulty.

 

Содержание MR-140









Отзывы:

Нет отзывов