background image

4

Selectable Inputs

The LSR4312SP subwoofer provides six discrete balanced analog XLR inputs (Left, Right, Center, Left 
Surround, Right Surround, and LFE) with sele4dBU / -10dBv sensitivity, as well as balanced ¼-
inch inputs for the Left and Right channels. In addition, dual high-resolution 96 kHz stereo AES/EBU and 
S/PDIF digital inputs are provided. This variety of inputs allows the LSR4312SP to be connected to a wide 
range of devices, including digital workstations, CD players, DVD players, and multichannel processors. 
What’s more, you can determine which input is to be monitored with the push of a button on either the 
front panel or wireless remote or click of a mouse (via an attached computer and LSR4300 Control Center 
software*).  

Other Features

•  12-inch self-shielded transducer with neodymium motor structure, self-powered with 450 watts 
of 
internal    amplifi cation, eliminating the need for external amplifi ers or speaker cabling. 

• Ultra-low frequency response to 20Hz, measured in-room.

• Advanced front-panel user interface allows control of system functions such as volume, solo, 
input selection, RMC initiation and bypass, bass management on/off, bass management crossover 
and LFE lowpass fi lter selection, and brightness level of the meter and buttons.

• Front panel meters show continuous output levels in dBFS.

• Built-in side handles aid in the positioning of the LSR4312SP subwoofer.

Note:

* Use of the wireless remote control and LSR4300 Control Center Software requires that the LSR4312SP 
subwoofer be used in a system with one or more LSR4328P or LSR4326P studio monitors. 

Introduction - Features

Содержание LSR4312SP






























































Отзывы: