background image

Instructions for CBT 1000+1000E System:

The 

BRACKET ASSEMBLY

 consists of 2 pieces of 

SPEAKER BRACKETS

 (the parts that mount on the 

speaker), 2 pieces of 

WALL BRACKETS

 (the parts that mount on the wall), 2 pcs of 

SWIVEL BRACKETS

 

(which get added to the 

SPEAKER BRACKETS 

if utilized for horizontal swivel/pan aiming capability), and an 

ARM LINK

 (which is utilized for the larger tilt angles). 

1) RUN WIRING

 -- Run the wiring from the power amplifier to the location desired for mounting the JBL 

CBT Loudspeakers.     Note:  Connect wire to speaker terminals at a point in the installation process when 

convenient for your installation circumstances.

2) ATTACHING WALL BRACKET TO WALL --

 Using a level to ensure that the 

WALL BRACKET 

is straight, 

secure the 

WALL BRACKET

 to the wall. Be sure to use the appropriate wall anchors for attaching the 

bracket. Use as many of the screw holes as possible for maximum integrity and safety.

 

CAUTION:   Installation must be done by qualified persons 

using safe rigging standards.

The installer is responsible for proper selection and use of mounting hardware 

to properly and safely wall-mount the speakers.

Hardware attaching 

WALL BRACKET 

to wall is not 

included.  Utilize proper hardware for particular wall 

structure.

Spacing needed between upper and lower  

WALL BRACKET 

parts with CBT1000 and 

CBT1000E depends on whether speaker will be set 

with down-tilt or up-tilt

Spacing:

1200 mm (47-1/4”) for Down-Tilt

1216 mm (47-7/8”) for Up-Tilt

9

(Drawings show upper 

and lower bracket 

orientation as set for 

down-tilt or 0°. Wall 

brackets to be reversed 

in location and flipped for 

up-tilt applications (see 

further instructions).

Содержание CBT1000





























Отзывы: