JBL AVR480 Скачать руководство пользователя страница 19

Страница: 19 / 52

Speaker Setup

This setup tells the AVR480 which type
of speakers are in use. This is important
as it adjusts the settings that determine
which speakers receive low-frequency
(bass) information and whether a center
speaker should be used or not. The
speakers may be configured independ-
ently for each source input, but it is rec-
ommended that the speakers be config-
ured the same for all inputs to ensure
optimum performance.

For each of these settings use the

LARGE

setting if the speakers for a

particular position are traditional full-
range loudspeakers that are capable
of reproducing sounds below 100Hz.
Use the

SMALL

setting for smaller,

frequency-limited satellite speakers that
do not reproduce sounds below 100Hz.
Note that when “small” front (left and
right) speakers are used, a subwoofer
is required to reproduce low-frequency
sounds. If you are in doubt as to which
category describes your speakers, con-
sult the specifications in the speakers’
owner’s manual, or ask your dealer.
Remember that each speaker setup that
differs from the default settings must be
made individually for each input in use.

It is best to select the Dolby Pro Logic II
Movie mode for speaker setup. Then with
the currently selected input all speaker
settings will be copied to other surround
modes (as far as possible) and need not
be repeated with any other mode.

With the AVR480 turned on, follow these
steps to configure the speakers:

1. Put the AVR480 in the Dolby Pro Logic II

Movie mode either by pressing the

Surround Mode Selector Button

on the front panel repeatedly, or by
pressing the

Surround Mode

Selector

and then the remote’s

⁄

Buttons

, until

DOLBY

PRO LOGIC II MOVIE

appears

in the

Main Information Display

and the

Pro Logic II Indicator

lights.

2. Press the

Speaker Button

FNT SPKR

will appear in the

Main

Information Display

3. Press the

Set Button

4. Press the remote’s

⁄

Buttons

or the

Selector Buttons

on the

front panel until either

F-

LARGE

F-SMALL

appears, matching the

type of speakers you have at the left-

front and right-front positions, as
described by the definitions shown
above.

When

SMALL

is selected, low-

frequency front-channel sounds will be
sent only to the subwoofer output. Note
that if you choose this option and there is
no subwoofer connected, you will not hear
any low-frequency sounds from the front
channels. This setting is not available
with stereo mode to ensure purest sound
by bypassing the crossovers of the DSPs.

When

LARGE

is selected, a full-range

output will be sent to the front left and
front right outputs. Depending on the sub-
woofer configuration (see below), the
front left and right bass information may
also be directed to a subwoofer.

IMPORTANT NOTE:

When a speaker

set with two front satellites and a
passive subwoofer connected to the

Front Speaker Outputs

is used, the

front speakers must be set for

LARGE

5. When you have completed your

selection for the front channels, press
the

Set Button

, and then press

the

⁄

Buttons

on the remote

or the

Selector Buttons

on the

front panel to change the display to

CEN SPKR

6. Press the

Set Button

on the

front again, and use the

⁄

Buttons

on the remote, or the

Selector

Buttons

on the front panel, to

select the option

(C-SMALL,

C-NONE, C-LARGE)

that best

describes your system based on the
center speaker definitions shown in
the preceding section.

When

SMALL

is selected, low-frequency

center channel sounds will be sent to the
fronts, if they are set for

LARGE

and

the Sub is turned off. When the Sub is
on, low-frequency center channel sounds
will be sent to the subwoofer only. (This
setting is not available when one of the
Logic 7 surround modes has been selected.)

When

LARGE

is selected, a full-range

output will be sent to the center speaker
output, and with analog and digital sur-
round modes (except with the Pro Logic II
Music mode) NO center channel signal
will be sent to the subwoofer output.

When

NONE

is selected, no signal will

be sent to the center channel output. The
receiver will operate in a “phantom” cen-
ter channel mode and center channel
information will be sent to the left and

right front-channel outputs and its bass
will be sent to the subwoofer output as
long as

SUB L/R+LFE

is selected

in the

SUBWOOFER

line in this menu

(see below). This mode is needed if no
center speaker is used. In this case, con-
sider selecting one of the DSP surround
modes, such as Hall or Theater.

7. When you have completed your

selection for the center channel, press
the

Set Button

, and then

press the

⁄

Buttons

on the

remote or the

Selector Buttons

on the front panel to change the
display to

SUR SPKR

8. Press the

Set Button

again,

and then use the

⁄

Buttons

on the remote or the

Selector Buttons

on the front panel to select the

option

(S-SMALL, S-NONE,

S-LARGE)

that best describes

your system based on the surround
speaker definitions shown in the pre-
ceding section.

When

SMALL

is selected, with all digi-

tal surround modes low-frequency sur-
round channel sounds will be sent to the
Fronts when the Sub is turned off, or to
the subwoofer output when the Sub is
on. With the analog surround modes the
rear bass feed depends on the mode
selected and the setting of the sub and
front speakers.

When

LARGE

is selected, a full-range

output will be sent to the surround chan-
nel outputs (with all analog and digital
surround modes), and, except with Hall
and Theater modes, NO surround channel
bass will be sent to the subwoofer output.

When

NONE

is selected, surround

sound information will be split between
the front-left and front-right outputs.
Note that for optimal performance when
no surround speakers are in use, the
Dolby 3 Stereo mode should be used.

9. When you have completed your

selection for the surround channel,
press the

Set Button

, and

then press the

⁄

Buttons

the remote or the

Selector Buttons

on the front panel to change the

display to

S-W SPKR