www.jbctools.com
10
11
Tool Settings
Sleep delay
Set the time that the tool
will remain at the selected
temperature when in the
stand before entering
sleep mode. The tip tem-
perature will then drop to
the Sleep temperature.
Sleep temperature
This is the set tempera-
ture the tip reaches when
returned to the stand.
Fix one temperature
Fix a value within the
temperature range of the sta-
tion (90-450ºC/190-840ºF).
Temperature levels set
Similar to “Fix one temp”
parameter. In this case, the
user can set up to 3 values for
different power requirements.
The sleep temperatures
are set to achieve a ba-
lance between preventing
oxidation and reaching the
working temperature in a few
seconds.
Ideal for soldering more than
one component at a specific
temperature. The station will
reject any attempt to change
the temperature.
This allows a quick change
between 3 different tempe-
ratures. Set them according
to the allowed values for your
soldering applications.
Because our tools reach the
working temperature from the
deafult Sleep mode in only a
few seconds, this parameter
is preset to 0 min. Once the
tool is returned to the stand
the temperature will automati-
cally drop to the sleep tempe-
rature, extending tip life and
avoiding oxidation. Retinning
the tip before placing the tool
in the stand will protect the tip
and extend its life.
Recommendations
Parameter description
Warnings
N/a
N/a
Setting these
parameters to higher
values will unnecessarily
accelerate oxidation
and shorten tip life
especially when working
with temperatures up to
450°C (840°F).
Parameters
Station Settings
Minimum temperature
Set the minimum
temperature to work
with.
Min. temp. by default is
200ºC (392ºF). This
is considered to be a
proper starting point for
leaded applications.
Maximum temperature
Set the maximum
temperature to work
with.
Max. temp by default is
400°C (750°F). This is
considered high enough
to work with most lead-
free applications.
Temperature unit
Celsius (ºC) or Fahrenheit (ºF)
Metronome
This activates a beep sound.
Frequencies vary from 1 to 50
seconds.
Help text
Activate this parameter to
receive info from the system.
Beep
enable/disable the beep
sound of the keypad.
Change pin
Change the default security
PIN number (0105).
Recommendations
Parameter description
The PIN must be entered
every time a parameter is
changed.
Useful for setting a work rate
in repetitive jobs. The beep
lets you know the length of
time the tip must be in con-
tact with the soldering joint.
N/a
N/a
N/a
Warnings
The station temperature
range is 90-450ºC
(190-840ºF). Change the
temperature limits when
working with less common
applications such as low /
high melting point solde-
ring (HMP) or plastics (e. g.
riveting).
N/a
N/a
N/a
N/a
In most cases,
working with temperatures
over 400°C (750°F) can
damage the PCB and its
components. even in short
time periods of tip contact
with the soldering joint, the
flux may not work properly
and could seriously reduce
tip life.
If the solder joint requires
more power (e.g. multila-
yered or high dissipation
boards), JBC strongly
recommends using other
aids like preheaters.
Should you wish to modify the locked parameters ( ), please fill in the form on
www.jbctools.com/en/form
and JBC will contact you. Be careful when using these parameters
as they may reduce the tip life if not used properly. Please follow the recommended guidelines:
Содержание CP-E
Страница 1: ...www jbctools com Compact Micro Tweezers Station Ref CP e English 2 Page Deutsch 34 Español 18 中文 48 ...
Страница 9: ...www jbctools com 16 17 Estación con Micro pinza Ref CP e ...
Страница 17: ...www jbctools com 32 33 Station mit Mikro Entlötpinzette Ref CP e ...
Страница 32: ...www jbctools com 62 63 Exploded View Despiece Explosionszeichnung 分解图 ...