Tool
ON
MENU
28174
24 W 100%
18 W 100%
12 W 100%
6 W 100%
0 W 100%
10 seconds/div
V1.2
CHARGE
450 ºC
350 ºC
250 ºC
150 ºC
50 ºC
JBC
210
348ºC
5,7 W
80%
350ºC
Tool
ON
MENU
24 W 100%
18 W 100%
12 W 100%
6 W 100%
0 W 100%
10 seconds/div
V1.2
WORK
450 ºC
350 ºC
250 ºC
150 ºC
50 ºC
80%
JBC
210
350ºC
Tool
ON
MENU
24 W 100%
18 W 100%
12 W 100%
6 W 100%
0 W 100%
10 seconds/div
V1.2
CHARGE
450 ºC
350 ºC
250 ºC
150 ºC
50 ºC
JBC
210
348ºC
5,7 W
80%
350ºC
JBC#1
JBC#1
MENU
Tool1
2822
Tool ID
Hibernation delay
Temperature units
00:30
Maximum Temperature
400ºC
Sleep mode
Sleep temperature
150ºC
Working
Low battery
Power OFF
Charging
No cartridge
Tool Status
ºC
ºF
JBC
210
Lock Parameters
Locked
Unlocked
Return to Work
Tool1
Tool ID
28714
Hardware
Software
0028283
X886787
Update File
File
Hardware
Software
Select your Firmware
-
-
Update
MENU
JBC
210
Return to Work
JBC#1
2822
Work
Settings
Counters
Update
Documents
Light Theme
Dark Theme
Disconnect
JBC#1
Update
Tool
ON
MENU
JBC#1
24 W 100%
18 W 100%
12 W 100%
6 W 100%
0 W 100%
10 seconds/div
V1.2
WORK
450 ºC
350 ºC
250 ºC
150 ºC
50 ºC
80%
JBC
210
350ºC
Tool1
Tool1
Tool1
Tool1
Tool2
Tool3
Tool
ON
MENU
24 W
18 W
12 W
6 W
0 W
10 seconds/div
V1.2
CHARGE
450 ºC
350 ºC
250 ºC
150 ºC
50 ºC
JBC
210
80%
350ºC
JBC#1
348ºC
6 W
10
10
1
6
7
Status Lightband
see table at the right
Safety Cap
Safety Cap and Cap Holder
Cap Holders
Status Lightband Detail
7. Tool Selection
Screw
Color
Battery Status
green
more than 50% charged
orange
between 20% and 50% charged
red
less than 20% charged
green
blinking
charging
(more than 50% charged)
orange
blinking
charging
(between 20% and 50% charged)
red
blinking
charging
(less than 20% charged)
no
color
safety cap on the handle
and/or power off
Thanks to the safety cap for B·IRON handles,
they can be safely transported even with a
cartridge inserted.
When the cap is placed onto the handle, the
cartridge stops heating
immediately,
data
transfer is cut off and the handle is disconnected
from the station. It turns off completely after 10
minutes of inactivity. This allows a greater saving
of the handles battery.
The charging base has a holder for two safety
caps on the back. This component can be
detached by loosening and removing the screw
in middle of the two holders (1).
While the tool is being used, the cap can be
stored on the cap holder.
Select the tool from the device list. If the tool is
not displayed on screen, make sure that the cap
is off and the tool has some battery. Try scanning
again by tapping
Scan
(6) on the display.
To add a second tool to the station once the fi rst
one is connected, go to the main menu (7) and
tap
Add device
. Select your second tool from
the device list.
Safety Cap
Holders
Fitting the safety cap to the handles, they can be
safely transported even with a cartridge inserted.
If so, the cartridge stops heating
immediately,
data
transfer is cut off and the handle is disconnected
from the station.
Handles turn off completely after 10 minutes of
inactivity and this allows a greater saving of the
handles battery.
While the handle is being used, the cap can be
stored on the safety cap holder at the back of the
charging base.
Tool Selection
Safety Cap
5
40 mm
50 mm
60 mm
80 mm
100 mm
130 mm
130 mm
para manuales - color gris
200 mm
300 mm
