background image

- 19 - 

P9

DMX MODE - setting the operation mode

The P9 Beamspot has 2 operating modes (see channel assignment for P9 Beamspot on page 
24). All parameters of P9 Beamspot can be operated via mode 1. However, all channels (except 
pan/tilt) are controlled with 8 bits. By selecting Mode 2 - 16 Bit the gobo, prism rotation, CMY/
CTO(CTB), dimmer, focus, zoom, the complete shutter slide unit as well as pan/tilt are controlled 
via 16 Bit.

CAMERA MODE - setting the repetition frequency of the LEDs

To avoid flickering during TV recordings, the P9 Beamspot can be adjusted from 50 HZ (PAL, 
Secam,  

repetition rate 100Hz) to 60 HZ (NTSC, repetition rate 100Hz) for different camera 

systems. Flex mode (repetition rate 600Hz is set when using different camera systems or when 
shooting with mobile phone cameras or similar non-professional cameras. A HighFlex mode is 
also available. In this mode, the repetition frequencies are set to 3 kHz, which is necessary to 
ensure smooth movements in dimmed lighting scenes. The factory setting of the P9 Beamspot is 
60 Hertz. The changeover is also possible with the light mixing console via the control channel.

COOLING MODE - adjustment of brightness and fan volume

In the COOLING MODE menu item you can set the fan control and the brightness of the P9 
Beamspot. The following settings are available.
THEATRE WHISPER: volume 29dB(a). In this mode, the spotlight runs at the same brightness up 
to an ambient temperature of 40°C. It is not necessary to speed up the fans in this mode.
THEATRE SILENT: from 40°C ambient temperature the spotlight regulates the fans a little up thus 
remains that the brightness is always the same level.
STANDARD: from an ambient temperature of approx. 36°C the fans run to cool the LED accord-
ingly. The brightness remains constant.
BOOST: Brightness 15000 lm, the fans run a little stronger in this mode, from approx. 40° ambi-
ent temperature the fans run again accordingly.
LONGLIFE: the fans run a little stronger in this mode, from approx. 40° ambient temperature the 
fans run again accordingly. We would recommend this mode for permanent installations, as the 
LED module runs cooler and thus more “stress-free”.

CURVES - setting dimmer, RGB/CMY, frost curve

Dimmer curve:
The dimmer curve can be changed from SQUARE to LINEAR and to SQUARE INV.. The 
“exponential” dimmer curve (factory setting) causes the dimmer to fade in and out more smoothly.
RGB/CMY curve:
3 different curves can be set for the RGB / CMY curve. SQUARE INV. LEGACY is the original 
curve of the P9 Beamspot. The SQUARE-INV.LEGACY curve causes a visually more uniform 
retraction. LINEAR and SQUARE INV., Are the two adapted curves on the P18 MK2.
Frost curve:
The frost curves can be changed from linear to invers exponential (square inv.). The “invers 
exponential” frost curve causes the frost to fade in and out more smoothly.

DMX OUTPUT CONFIG - configuration of the DMX output

Under this menu item, the DMX output of the headlamp can be activated, that is a received Art-
net, or wireless DMX signal can be output by activating this menu item -> ON via the DMX socket 
again. Make sure that there is no signal at the DMX input at the same time !!

Under IP ADDRESS -> DEFAULT IP this can be changed from the network 10.xxx.xxx.xxx to a 
network 2.xxx.xxx.xxx. For your own self-definable IP address, you can set your own desired IP 
address under IP ADDRESS -> USER-IP. This address is divided into BYTE1 to BYTE 4 and can 
be set one after the other.

Содержание P9 Beamspot













































Отзывы: