![background image](http://html1.mh-extra.com/html/jayco/north-point-2023/north-point-2023_owners-manual_3662292041.webp)
35
Section 4: Vehicle Operation
Towing Behind Your RV
NOTE: IF YOU DO NOT HAVE A JAYCO FACTORY INSTALLED HITCH
RECEIVER, DO NOT TOW ANYTHING BEHIND YOUR RV. THE RV
FRAME AND BUMPER ARE NOT DESIGNED FOR TOWING.
NOTE: A hitch equipped for trailer towing will have tabs to hang the safety
chains and there will be a bracket for the trailer wiring plug. There should
also be a label on the hitch stating maximum towing capacity.
If you do not have a
Jayco factory installed hitch receiver,
towing items
behind your Jayco RV, or overloading the rear, will void the warranty and may
result in: damage to the RV or add-on items, towing difficulties, property dam
-
age and/or personal injury.
Breakaway Switch
Your RV may be equipped with a breakaway switch. The breakaway switch is a crucial part
of the RV braking system. Located on the travel trailer A-frame, or beside the fifth wheel
pinbox, this switch will apply the RV brakes if the trailer becomes detached from the tow
vehicle. Attach the breakaway switch lanyard to a permanent part of the tow vehicle when
hitching your RV. On a travel trailer, do not attach it to the hitch ball or similar removable
parts. If the RV becomes detached from the tow vehicle, the pull pin will be pulled from the
switch. This automatically causes the switch to “close” and activates the RV brakes
.
Hydraulic Brakes (if so equipped)
Your RV may be equipped with hydraulic surge brakes that operate automatically as the tow
vehicle’s brakes are applied. When speed is decreased and brakes are applied, the weight of
the trailer moving forward creates a reaction, which causes the brake fluid inside the wheel
cylinder to activate the brake shoes against the drum.
As a result of this design, backing the RV uphill may activate the surge brake system making
it difficult to continue in reverse. To aid in backing up the RV:
1.
Prior to backing up a slope or through soft ground, pull the recreation vehicle forward
slightly to assure that the actuator socket is in the forward position.
2.
Move the lever on the side of the actuator downward from the “towing position” along
the curved slot in the actuator frame to the “backup position.” The slot has a notch at
the bottom of its travel. Push the lever down to engage the locking notch.
3.
The RV will now back up. This lever will slide into the correct position when pulling
forward.
It is extremely important to keep the master cylinder full at all times. An empty cylinder
invites moisture.
Disc Brakes (if so equipped)
If your RV is equipped with disc brakes, see the manufacturer’s owner’s manual for detailed
safety and maintenance information.
NEVER use the breakaway switch and trailer brake system as a parking
brake.
Doing so would create a high amp draw on the battery and converter.
This can cause damage to wiring, connectors and the breakaway switch.
Table of Contents
Содержание NORTH POINT 2023
