![background image](http://html1.mh-extra.com/html/jayco/eagle-eagle-super-lite/eagle-eagle-super-lite_owners-manual_3560112066.webp)
SECTION 9
SLIDEOUT SYSTEMS
62
corners of the black rubber seal are set up
correctly. The corners of this seal are cut at a
45° angle. The top of the seal must overlap
the side of the seal to avoid the possibility of
water penetration.
Retracting slideout room
Press the IN section of the slideout control
switch and hold it until the motor stops.
Operating the switch after the room is fully
retracted will damage the switch and motor.
Maintenance
Your slideout system has been designed to
require very little maintenance. To ensure a
long life of your slideout system, read,
understand and follow these simple
instructions. This system contains a pre-lubed
bearing that is lubricated when the room is
moved in and out. Do not spray oil or grease
on the rails while the room is extended.
T
ROUBLESHOOTING
T
HE
S
LIDEOUT
If the slideout does not move when the
slideout switch is depressed, follow these
steps.
Check the auxiliary battery (customer
supplied) for a full charge and good wire
connections.
Check the 12-volt fuse or circuit breaker.
Check for loose connections at the
slideout motor.
If the slideout still will not operate, follow
these steps.
If the slideout is extended, refer to the
following section on overriding the specific
slideout system installed on your RV.
If the slideout is retracted, leave it in that
position.
Contact your dealer or Jayco Customer
Service for repair assistance.
If the slideout extends crooked or only one
side moves, follow these steps.
Follow steps on overriding the specific
slideout system installed on your RV.
You may need to push the side that is not
sliding to get it to retract all the way.
Contact your dealer or Jayco Customer
Service for repair assistance.
V-tech slideout override
If the RV has an
underbelly, locate and
remove the access
panel to access the
slideout motor (this
panel is typically under
the RV on the opposite
side of the slideout
room). Use a 3/4 socket
and ratchet on the hex
head located on the end of the drive shaft.
Turn the drive shaft until the slideout is in the
position you desire. Contact your RV dealer
for service.
Dexter Chassis Group (DCG) Center Drive
Slide override (flush floor models)
Disconnect the
slideout motor
brake wires from
the power wires.
Connect a 9 volt
battery harness to
the motor brake
wires Locate the
manual advance
crank nut on the
backside of the
motor. Crank the
nut on the slideout motor with a 5/8” socket.
With the 9 volt battery connected to the motor
brake crank the nut on the motor until the
room is sealed. Once the slide is in a closed
position remove the 9 volt battery and
harness.
Fig. 9.5 DCG manual
advance crank nut
Do not work on your system unless the 12-
volt DC (auxiliary battery, customer
supplied) and 120-volt AC electrical
systems (shore line power cord) have
been disconnected.
Fig. 9.4 V-tech
slide hex head
Содержание Eagle Eagle Super Lite
