![background image](http://html1.mh-extra.com/html/jayco/eagle-eagle-super-lite/eagle-eagle-super-lite_owners-manual_3560112031.webp)
SECTION 4
TOWING & HANDLING
27
W
IRE
H
ARNESS
/C
ONNECTOR
P
LUG
A 7-way wire harness/connector plug is wired
into your trailer to connect electrical power
from the tow vehicle for travel. This supplies
power to the RV brakes, tail lights, clearance
lights, turn signals, brake lights, etc. Wiring to
operate your brakes must be the same size in
both the tow vehicle and RV (the RV brake
wiring is 12-gauge wire). When attaching
wires to your tow vehicle, carefully and tightly
tape all the connections for moisture
protection.
White 1 Ground
Blue 2
Brakes
Green 3 Running
lights
Black
4 Auxiliary battery charge line
Red
5 Stop & left turn
Brown 6 Stop & right turn
Yellow 7 Back up
The connector plug may build up corrosion
with extended use and should be cleaned
periodically to insure good electrical contact.
Make sure the connector plug is kept clean
and protected from road elements as you
travel.
S
TABILIZER
J
ACKS
1. Each stabilizer jack can be individually
adjusted to stabilize the trailer for use.
2. When setting your RV up on soft ground,
you may wish to place a wood pad or the
equivalent under each stabilizer jack foot.
This will help keep the stabilizer jack from
sinking into the ground.
3. To lower each jack, insert the jack crank
onto the applicable stabilizer jack shaft.
4. Turn the crank clockwise to lower each
leg until it contacts the ground and
stabilizes the trailer.
To raise each jack, insert the jack crank onto
the applicable stabilizer jack shaft and turn
the crank counter-clockwise.
The stabilizer jacks must be fully retracted
before moving or towing the RV to prevent
stabilizer jack damage.
T
RAVEL
T
RAILER
H
ITCHING
P
ROCEDURE
Hooking up your RV will become easier with
practice. The following procedure will help
until you become more experienced.
1. Make sure the trailer wheels are blocked.
2. Turn the tongue jack crank to raise the
travel trailer tongue above the hitch ball.
3. Open the coupler latch on the travel trailer
hitch.
4. Back the tow vehicle into the proper
position.
5. Turn the tongue jack crank to lower the
coupler onto the hitch ball.
6. Close the coupler latch after it is
completely seated.
7. Install the (customer supplied) weight
distributing bars (equalizers) as directed
by the OEM.
8. Remove the dolly wheel or platform and
retract the tongue jack to its maximum
height.
9. Attach the breakaway switch cable to the
tow vehicle.
Fig. 4.2
7-way trailer plug
Car end, rear view
DO NOT USE THE STABILIZER JACKS
TO LEVEL THE RV.
It is important to
remember that the stabilizer jacks are to
be used only for support while occupying
and moving around the RV. They are not
designed to bear the weight of the RV.
Содержание Eagle Eagle Super Lite
