background image

Keys and LEDs

FN Key and REC LED

8

 

                                                                                                              

     

www.javad.com

• Pressing the FN key for more than one and less than five seconds will start/stop data recording. 

During data recording the REC LED is green or orange. If the REC LED is red, the receiver has
run out of memory, has a hardware problem, or contains an improper OAF.

• The REC LED blinks green or orange each time data is written to the internal receiver's memory.

You set the data recording time interval using TriVU Software. See TriVU Software Manual for
information on setting this function.

Each time you turn off or on data recording, either a new file opens or data appends to a particular
file.

• Pressing the FN key for more than five and less than eight seconds will turn the baud rate of serial

port A to 9600. After about five seconds of pressing the FN key, the REC LED becomes red.
Release the FN key while the REC LED is red (during the next three seconds).

• Pressing the FN key for more than eight seconds has no impact.

• After loading new firmware or clearing the receiver's NVRAM, the receiver checks its internal file

system.

During this operation, the REC LED flashes orange, and the file system is not accessible for CDU
(control display unit) applications or for data recording. This operation may require from fractions
of a second to several minutes, depending on the circumstances and the amount of internal mem-
ory.

Table 1. FN Key Functions and REC LED Status

FN Key

REC LED

Status

When data recording is OFF, and the FN key is...

Not pressed

No light

No data recording.

Orange blink

Internal file system test in progress.

Red

No free memory; hardware problem with data recording.

Pressed for < 1 second

If FN key mode is «LED blink mode switch»

Orange

Release to charge information mode.

If FN key mode is «Occupation mode switch»

Orange

No function.

Pressed for 1–5 seconds

If FN key mode is «LED blink mode switch»

Green

Release to start data recording (post-processing occupation mode 
undefined).

If FN key mode is «Occupation mode switch»

Green

Release to start recording (Kinematic or Static post-processing 
occupation mode).

Pressed for 5–8 seconds

Red

Release to turn serial port A baud rate to 9600 bps.

Pressed for > 8 seconds

No light

No function.

Содержание TriPad











Отзывы: