specifications, installation,
operation and maintenance instructions
Model SER 200/400
page 6 of 8
®
JARVIS
6205010::::.
PRODUCTS CORPORATION
33 ANDERSON ROAD, MIDDLETOWN, CONNECTICUT 06457--4926
UNITED STATES OF AMERICA E--MAIL.
TEL. 860--347--7271 FAX. 860--347--6978 WWW. j
arvisproducts.com
SPECIFICATIONS
Motor Power
1.7 hp
1300 W
Operating Volt/Amp
42V/33A, 1 phase, 50/60 Hz
115V/12A, 1 phase, 50/60 Hz
230V/6A, 1 phase, 50/60 Hz
Stroke
1.6 in
41 mm
Blade Speed
8500 strokes / min
Control Handle
Single
Electric
Blade Length
8 in
203 mm
16 in
406 mm
Overall Length (w/o blade)
18.0 in
457 mm
Weight (w/o blade)
16 lbs
7.2 kg
Vibration
135 dB Front
136 dB Rear
Noise (one meter from tool)
93 dB
INSTALLATION INSTRUCTIONS
1 Install the saw above the work station from a balanc-
er if desired.
Jarvis
part number 4042040 is avail-
able.
2 Position power cord (item 31) for either top exit or
rear exit, as desired.
2.1 Unplug the tool.
2.2 Remove four (4) pan head screws (item 37),
electrical box cover (item 38) and gasket (item
39).
2.3 Disconnect power cord from switch (item 41).
2.4 Remove two (2) locking nuts (item 29), strain
relief connector (item 30) and plug (item 32).
2.5 Swap positions of strain relief and plug. Re--
tighten nuts.
2.6 Reconnect power cord to switch.
2.7 Reinstall gasket, cover and four (4) screws.
3 Plug the 42 V, 50/60 Hz model into a 42 V power
supply. Plug the 115 V, 50/60 Hz model into a stan-
dard 115 V wall outlet. Plug the 230 V, 50/60 Hz
model into a standard 230 V wall outlet.
OPERATION INSTRUCTIONS
1
Test
the tool prior to use.
Depress
the trigger and the
tool should start.
Release
the trigger and the tool
should stop.
If the tool malfunctions, remove it from
service and report the problem to your supervisor
immediately.
2 Make sure that the saw moves freely on the balancer.
3 Making the cut.
3.1 Position the saw.
3.2 Depress the trigger to start the saw and make the
cut.
3.3 When the desired length of cut is reached, re-
lease the trigger. This will stop the blade from
oscillating.
Continue holding the saw firmly
with both hands until the blade stops oscillat-
ing.
3.4 Withdraw the saw blade from the carcass.
MAINTENANCE INSTRUCTIONS
IMPORTANT: ALWAYS DISCONNECT THE ELECTRIC POW-
ER SUPPLY BEFORE PERFORMING ANY REPAIRS OR
MAINTENANCE.
1 MONTHLY:
1.1 Remove six (6) flat head screws (item 71), six
(6) countersink washers (item 72), bottom cover
(item 73) and gasket (item 74).
1.2 Ensure that gear case is 3/4 full of USDA ap-
proved grease.
Jarvis
part number 1062003 is
available. Add grease if necessary.
1.3 Replace gasket, bottom cover, washers and
screws.
2 BLADE DISASSEMBLY:
Always wear cut protective gloves when handling
blades.
2.1 Remove two (2) lock nuts (item 64) and two (2)
socket head cap screws (item 69).
2.2 Slide blade (item 93, 95 or 97) off blade support
(item 92, 94 or 96).
2.2.1 Push drive ram (item 63) into housing if
more space is required for blade removal.
3 BLADE ASSEMBLY (item 93, 95 or 97):
3.1 END CUTTING BLADE (item 93)
3.1.1 Slide blade (item 93) onto blade support
(item 92) until crimp in end of blade is
touching end of support.
3.1.2 Use soft mallet to tap end of blade toward
body of saw until the crimp in the blade
slides into the slot in the blade support.
