Janome MEMORY CRAFT 4800 страница 36 Скачать руководство пользователя

Страница: 36 / 68

•

Sewing preparation

Stitch pattern:

Presser foot:

Automatic buttonhole foot R

* When you select the buttonhole stitch, the screen

indicates the message: “PULL DOWN BH (Button

hole) LEVER” for a few seconds.

[1]

Attach the automatic buttonhole foot R.

Make sure the groove on the holder catches the pin

on the foot, when lowering the presser foot.

Groove

[2]

Pull the button holder to the back, and place the

button in it.

Push it together tightly on the button.

Button holder

If the button is extremely thick, make a test button-

hole.

If it is difficult to fit the button through the test

buttonhole, lengthen the size by pulling the button

holder on the back to increase length.

Gap

[3]

Pull the buttonhole lever down as far as it will go.

Buttonhole lever

[1]

[2]

[3]

Содержание MEMORY CRAFT 4800





































































Результаты поиска

Содержание MEMORY CRAFT 4800

Отзывы:

Похожие инструкции для MEMORY CRAFT 4800

Бренды по названию

Популярные бренды

Janome MEMORY CRAFT 4800, Инструкция

Результаты поиска

Содержание MEMORY CRAFT 4800

Отзывы:

Похожие инструкции для MEMORY CRAFT 4800

Бренды по названию

Популярные бренды